Husqvarna FS 1000 E Скачать руководство пользователя страница 6

Страница: 6 / 15

•

Set up a barrier or signs around the working area to

prevent any unauthorised personnel from being injured

or disturbing the operator while working.

•

Check the belt tension as described in section 5.3. Adjust

if necessary using the belt tensioning screw. Turning

clockwise tightens the belts.

•

Before you start cutting, plan your work and clearly mark

out the area you intend to cut so that you can carry out

the work without risk of injury or damage to the machine.

See figure 3.1.

•

To avoid interruptions and inconvenience during cutting,

plan your work so that you fit the blade on the most suita-

ble side of the saw right from the start.

• Check that you have the right diamond blade for the

FS 1000 EM and the material you intend to cut.

See section 9 Technical specifications.

•

Check the direction of rotation before fitting the blade.

Raise the blade guard on the side where you want to fit

the blade. Secure the blade guard with the retaining

strap. Connect the power cable and press the switch to

start the machine. Check that the blade flange rotates in

the direction shown by the arrow on the blade guard. If

the flange rotates in the wrong direction, turn off the

switch to stop the machine, then unplug the power cable

from the machine. Change the setting of the phase inverter

on the control panel. Stop the machine as described

above and recheck.

•

Check that the blade is not worn; each of the diamond

segments must project at least 1 mm. They must also be

wider than the body of the blade. See figure 6.3.

•

Check that none of the diamond segments is damaged.

•

Fit the blade so that the arrow on the body of the blade

matches the direction of rotation of the shaft. Tighten

the blade flange using the pin spanner supplied, while

using the other spanner to prevent the blade shaft from

turning. See the instructions in section 6, Fitting and

replacing diamond blades.

•

Lower the blade guard over the blade.

•

Check that the blade is straight by turning the blade by

hand and measuring the gap between the blade and the

blade guard. If the blade is misaligned or uneven it must

be replaced.

•

Check that both the blade guard and the blade flange

guard are correctly fitted, then lower them.

•

Make sure the emergency stop is not deactivated. The

emergency stop must not be deactivated during operation.

•

Before starting the floor saw, raise the blade so that it

rotates without touching the surface.

•

Connect the power cable to the power socket.

•

Connect the water-cooling hose to the coupling that runs

from the blade guard.

•

Check that the water supply is adequate and that the

nozzle is not blocked.

•

Make sure that the power cable and water-cooling hose

from the floor saw will not get trapped underneath or in

front of the machine when you start up or during cutting.

•

Use the safety equipment specified in the safety precau-

tions on page 5.

Figure 3.1.

4. Starting and operating

Before starting and operating the saw follow the steps in

section 3.

•

Lower the alignment guide and adjust it so that the tip of

the guide and the saw blade are in line.

•

Clear away any objects from the path of the machine that

could damage the machine or the surroundings.

•

Check that there are no unauthorised people inside the

working area, i.e. 4 metres in front of and to the side of

the machine.

•

Make sure that anyone who has to remain nearby is

wearing hearing protection.

•

Release the parking brake.

•

Line up the floor saw with the cutting line you have

marked on the floor.

•

Check that the saw blade rotates freely.

•

Check your safety equipment and any protective clothing

you are wearing.

•

Apply the parking brake.

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

;;;;;;;;;;;;;;;;;;;;

@@@@@@@@@@@@@@@@@@@@