Husqvarna FE 450 Скачать руководство пользователя страница 94

Страница: 94 / 128

15 ELECTRICAL SYSTEM

» If the light-dark border does not meet specifications:

–

Adjust the headlight range. (

p. 92)

15.11

Adjusting the headlight range

Preparatory work

–

Check the headlight setting. (

p. 91)

F00363-10

Main work

–

Loosen screw



–

Adjust the headlight range by pivoting the headlight.
Guideline

The boundary between light and dark must be exactly on the lower mark for

a motorcycle with driver (instructions on how to apply the mark: Checking the

headlight setting).

Info

A change in weight on the vehicle may require a correction of the headlight

range.

–

Tighten screw



15.12

Changing the speedometer battery

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the headlight mask with the headlight. (

p. 89)

F00370-10

Main work

–

Remove screws



with the washers.

–

Pull the speedometer upward out of the holder.

F00371-10

–

Using a coin, turn protection cap



all the way counterclockwise and remove it.

–

Remove speedometer battery



–

Insert the new battery with the label facing outward.

Speedometer battery (CR 2032) (

p. 114)

–

Check the O-ring of the protection cap for correct seating.

F00372-10

–

Position protection cap



and turn all the way clockwise using a coin.

–

Press any button on the speedometer.

The speedometer is activated.

–

Position the speedometer in the holder.

–

Mount and tighten the screws with washers.

Finishing work

–

Install the headlight mask with the headlight. (

p. 90)

–

Check the headlight setting. (

p. 91)

–

Set the speedometer. (

p. 21)

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды