Husqvarna FE 450 Скачать руководство пользователя страница 77

Страница: 77 / 128

13 BRAKE SYSTEM

F00329-11

–

Insert the new brake linings, insert pin



, and mount cotter pins



Info

Always change the brake linings in pairs.

–

Operate the hand brake lever repeatedly until the brake linings are in contact with

the brake disc and there is a pressure point.

F00312-10

–

Correct the brake fluid quantity to level



Guideline

Level



(brake fluid level below

reservoir rim)

5 mm (0.2 in)

Brake fluid DOT 4 (

p. 117)

–

Position cover



with membrane



–

Mount and tighten screws



Info

Clean up overflowed or spilled brake fluid immediately with water.

13.8

Checking the free travel of foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

402026-10

–

Disconnect spring



–

Move the foot brake lever back and forth between the end stop and the contact

to the foot brake cylinder piston and check free travel



Guideline

Free travel at foot brake lever

3… 5 mm (0.12… 0.2 in)

» If the free travel does not meet specifications:

–

Adjust the basic position of the foot brake lever.

(

p. 75)

–

Reconnect spring



13.9

Adjusting the basic position of the foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear brake.

–

Set the free travel on the foot brake lever in accordance with the specification.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды