Husqvarna FE 450 Скачать руководство пользователя страница 73

Страница: 73 / 128

13 BRAKE SYSTEM

13.1

Checking free travel of hand brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the hand brake lever, pressure builds up on the front brake circuit.

–

Set the free travel on the hand brake lever in accordance with the specification.

F00325-10

–

Push the hand brake to the handlebar and check free travel



Free travel of hand brake lever

≥

3 mm (

≥

0.12 in)

» If the free travel does not meet specifications:

–

Adjust the free travel of the hand brake lever. (

p. 71)

13.2

Adjusting free travel of hand brake lever

F00325-11

–

Check the free travel of the hand brake lever. (

p. 71)

–

Adjust the free travel of the hand brake lever with adjusting screw



Info

Turn the adjusting screw clockwise to reduce free travel. The pressure

point moves away from the handlebar.
Turn the adjusting screw counterclockwise to increase free travel. The

pressure point moves towards the handlebar.
The range of adjustment is limited.
Turn the adjusting screw by hand only, and do not apply any force.
Do not make any adjustments while riding!

13.3

Checking the brake discs

Warning

Danger of accidents

Worn-out brake discs reduce the braking effect.

–

Make sure that worn-out brake discs are replaced immediately. (Your authorized Husqvarna Motorcycles workshop will

be glad to help.)

400257-10

–

Check the thickness of the front and rear brake discs at multiple points on each

brake disc to ensure it is at least thickness



Info

Wear reduces the thickness of the brake disc around the area used by the

brake linings.

Brake discs - wear limit

Front

2.5 mm (0.098 in)

Rear

3.5 mm (0.138 in)

» If the brake disc thickness is less than the specified value:

–

Change the front brake disc.

–

Change the rear brake disc.

–

Check the front and rear brake discs for damage, cracking, and deformation.
» If the brake disc exhibits damage, cracking, or deformation:

–

Change the front brake disc.

–

Change the rear brake disc.

Содержание FE 450

































































































































Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды

Husqvarna FE 450, Руководство пользователя

Результаты поиска

Содержание FE 450

Отзывы:

Похожие инструкции для FE 450

Бренды по названию

Популярные бренды