Husqvarna 966503901 Скачать руководство пользователя | Manualshive

Страница: 42 / 56

background image

LUBRICAtIon

42

Front Wheel Mount

Lubricate with a grease gun, one zerk for each wheel
mount, until the grease is forced out.
Use only good quality bearing grease.
Grease from well-known brand names (petrochemical
companies, etc.) usually maintains a good quality.

Front Wheel Bearings

Lubricate with a grease gun, one zerk for each set of
wheel bearings, until the grease is forced out.
Use only good quality bearing grease.

IMPORTANT INFORMATION

Use minimal lubrication and remove excess
lubricant so that is does not come into contact
with belts or belt pulley drive surfaces.

8050-009

Lubricating the wheel bearings

Engine Lubrication

Refer to the engine manufacturer's manual for
maintenance and service instructions.

Steering Control Shafts

Tip the driver’s seat.
Lubricate with a grease gun, one zerk for each
steering control shaft, until the grease is forced out.
Use only good quality molybdenum disulphide
grease.
Grease from well-known brand names (petrochemical
companies, etc.) usually maintains a good quality.

8058-076

Lubricating the steering control shafts

«
...
40
41
42
43
44
...
»

Содержание 966503901

























































Отзывы:

Нет отзывов

Похожие инструкции для 966503901

Бренд: Yard-Man Страницы: 16

Бренд: Poulan Pro Страницы: 60

Бренд: EGO Страницы: 2

Z Master Professional 5000 Series

Бренд: Toro Страницы: 80

Бренд: Nakayama Страницы: 65

Pro Z 100 Lapbar

Бренд: Cub Cadet Страницы: 28

Бренд: RedMax Страницы: 28

Бренд: Yard-Man Страницы: 24

309006 190A Series

Бренд: Murray Страницы: 40

Бренд: Simplicity Страницы: 16

Бренд: Parkside Страницы: 124

Бренд: DR Страницы: 44

TH910 Series II

Бренд: Deutscher Страницы: 22

Бренд: OREC Страницы: 39

Бренд: Honda Страницы: 21

Бренд: RHINO Страницы: 160

Бренд: Yard-Man Страницы: 28

Бренд: Toyama Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды