Husqvarna 927SBEXP Скачать руководство пользователя страница 6

Страница: 6 / 32

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD
(See Figs. 3 and 4)

The traction drive control rod has the long loop on the end
of the spring as shown.

1. Slide rubber sleeve up rod and hook end of spring into

pivot bracket with loop opening down as shown.

2. With top end of rod positioned under left side of control

panel, push rod down and insert top end of rod into hole
in drive control bracket. Secure with retainer spring.

AUGER
CONTROL
ROD

CONTROL
ARM

RUBBER
SLEEVE

LOOP

OPENING

FIG. 5

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the
spring as shown.

1. Slide rubber sleeve up rod and hook end of spring into

control arm with loop opening up as shown.

2. With top end of rod positioned under right side of

control panel, push down on rod and insert end of rod
into hole in auger control bracket. Secure with retainer
spring.

TRACTION DRIVE

CONTROL ROD

PIVOT
BRACKET

RUBBER

SLEEVE

LOOP
OPEN ING
DOWN

FIG. 3

TRACTION
DRIVE
CON TROL
ROD

DRIVE
CONTROL
BRACKET

RETAINER

SPRING

TRACTION DRIVE
CON TROL LEVER

FIG. 4

AUGER

CONTROL

LEVER

AUGER CONTROL ROD

AUGER

CONTROL
BRACKET

RETAINER
SPRING

FIG. 6

Содержание 927SBEXP

































Результаты поиска

Содержание 927SBEXP

Отзывы:

Похожие инструкции для 927SBEXP

Бренды по названию

Популярные бренды

Husqvarna 927SBEXP, Руководство пользователя

Результаты поиска

Содержание 927SBEXP

Отзывы:

Похожие инструкции для 927SBEXP

Бренды по названию

Популярные бренды