Husqvarna 927SBEXP Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 32

background image

31

KEY PART
NO. NO.

DESCRIPTION

   1   532 19 95-01   Wheel Assembly, 16", Power Steering, LH
   2   532 15 54-43   Pin, Klik 1/4
   3   532 19 21-09   Cover, Power Steering
   4   532 18 44-71   Bolt, Shoulder #10-24 x 5/8
   7   871 21 06-16   Capscrew, Hex Head, Flanged 3/8-16 x 1
   8   532 18 78-59   Bracket, Steering Cable, RH
   9   532 18 78-58   Bracket, Steering Cable, LH

10 817 60 04-06 Screw, Hex Head 1/4-20 x 3/8

11 817 49 05-08 Screw, Hex Head 5/16-18 x 1/2

12   532 19 57-49   Link, Steering Lever
13   532 18 78-60   Yoke, Steering
14   532 18 20-15   Pin, Steering Lever
15   532 19 95-18   Bellcrank
16   532 19 95-12   Bracket Assembly, LH Steering
17   532 19 95-11 Bracket Assembly, RH Steering
18   532 18 18-47   Pin, Steering Bellcrank
19   532 08 51-79   Retainer, Hairpin
20   532 18 41-97   Bracket, Steering
21   532 19 21-26   Driver, Wheel
22   532 18 24-66   Ring, Wire Retainer
23   532 18 76-22   Lobe, Wheel
24   532 19 49-41   Slide, Clutch
25   532 17 91-39   Spring, Clutch Slide
26   532 19 49-40   Lobe, Axle
27   532 18 92-82   Key, Square
28   532 17 46-97   Washer, Thrust (1")
29   532 17 98-30   Bearing, Axle
30   532 19 38-85   Spring, Return
31   532 19 95-02   Wheel Assembly, 16", Power Steering, RH
32   532 70 02-79   Clip, Retainer
33   812 00 00-45   Ring, Retaining
34   532 14 63-15   Screw, Hex Head 5/16-18 x 5/8

KEY PART
NO. NO.

DESCRIPTION

   1   532 18 10-38   Decal, Danger
   2   532 19 13-76   Decal, Husqvarna
   3   532 18 10-34   Decal, Danger, Defl ector
   4   532 18 10-41   Decal, Danger
   5   532 19 87-39   Decal, Husqvarna, 927SBEXP
   6   532 18 10-32   Decal, Instruction
   7   532 15 57-98   Decal, Traction Lever
   8   532 15 58-00   Decal, Auger Lever
   9   532 18 10-36   Decal, Speed Control

10 532 18 37-29 Decal, Remote Defl ector

11 532 18 39-07 Decal, LH Trigger

12 532 18 39-05 Decal, RH Trigger
13 532 15 57-94 Decal, Husqvarna, Crown

- - 532 19 83-80 Owner’s Manual, English
- - 532 40 14-95 Owner’s Manual, French

REPAIR PARTS

WHEELS / DECALS

SNOW THROWER - MODEL NO.

927SBEXP

(96193000500), PRODUCT NO. 961 93 00-05

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your lawn mower and void your warranty.

«
...
29
30
31
32
»

Содержание 927SBEXP

































Отзывы:

Нет отзывов

Похожие инструкции для 927SBEXP

Бренд: Walker Страницы: 40

Бренд: e-breathe Страницы: 56

Бренд: ebm-papst Страницы: 11

Бренд: Garland Страницы: 124

Бренд: Zenoah Страницы: 60

Бренд: Troy-Bilt Страницы: 56

Бренд: Stark Страницы: 17

Бренд: MTD Страницы: 20

Бренд: Poulan Pro Страницы: 44

Бренд: Worx Страницы: 104

Бренд: The Handy Страницы: 12

Бренд: Texas Equipment Страницы: 12

Бренд: Meec tools Страницы: 98

Бренд: Poulan Pro Страницы: 24

Бренд: DONG IL TECHNOLOGY LTD Страницы: 23

Бренд: Snapper Страницы: 28

Бренд: Snapper Страницы: 32

Бренд: Snapper Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды