Husqvarna 8527SBE Скачать руководство пользователя страница 7

Страница: 7 / 32

ASSEMBLY / PRE-OPERATION

CHECK TIRE PRESSURE

The tires on your snow thrower were overinfl ated at the fac-
tory for shipping purposes. Correct and equal tire pres sure
is important for best snow throwing performance.

• Reduce tire pressure to 14-17 PSI (19-24.5 N-m).

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD
(See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may
be used to install the chute rotater head.

1. Place discharge chute assembly on top of chute base

with discharge opening toward front of snow thrower.

2. Position chute rotater head over chute bracket. If nec-

es sary, rotate chute assembly to align square and pin
on un der side of chute rotater head with holes in chute
brack et.

3. With chute rotater head and chute bracket aligned,

po si tion chute rotater head on pin and threaded stud
of mounting bracket.

4. Install 3/8 washer and locknut on threaded stud and

tighten securely.

INSTALL CHUTE DEFLECTOR REMOTE CONTROL
(See Figs. 8 and 9)
1. Install remote cable bracket to discharge chute with

5/16-18 carriage bolt, 5/16 fl at washer and 5/16-18
locknut as shown. Tighten securely.

2. Install remote cable eyelet to chute defl ector with

1/4-20 shoulder bolt, nylon friction washer and 1/4-20
locknut as shown. Tighten securely.

3. Install spring hooks between hex nuts on chute rotater

head and into hole in chute defl ector as shown.

CHUTE DEFLECTOR
CONTROL LEVER

FIG. 9

CHUTE
ROTATER
HEAD

3/8 WASHER

3/8 LOCKNUT

THREADED

STUD

PIN

ROTATER HEAD

MOUNT ING

BRACKET

CHUTE
BRACKET

FIG. 7

ALIGN BEFORE

TIGHTENING LOCKNUT

HOOK BE TWEEN

HEX NUTS

ON CHUTE

ROTATER HEAD

SPRING

CHUTE
DE FLEC TOR

5/16-18

CARRIAGE

BOLT

5/16-18
LOCKNUT

REMOTE
CABLE
BRACKET

1/4-20
LOCK-
NUT

FLAT

WASHER

CABLE
EYELET

NYLON
WASHER

1/4-20

SHOULDER

BOLT

FIG. 8

Содержание 8527SBE

































Результаты поиска

Содержание 8527SBE

Отзывы:

Похожие инструкции для 8527SBE

Бренды по названию

Популярные бренды

Husqvarna 8527SBE, Руководство пользователя

Результаты поиска

Содержание 8527SBE

Отзывы:

Похожие инструкции для 8527SBE

Бренды по названию

Популярные бренды