Husqvarna 701 Enduro 2017 Скачать руководство пользователя страница 118

Страница: 118 / 216

13 BRAKE SYSTEM

116

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service schedule. (Your authorized

Husqvarna Motorcycles workshop will be glad to help.)

V00516-10

–

Stand the vehicle upright.

–

Check the brake fluid level of the brake fluid reservoir.
» If the fluid level reaches the

MIN

marking



–

Add rear brake fluid.

(

p. 116)

13.11

Adding rear brake fluid

Warning

Danger of accidents

An insufficient brake fluid level will cause the brake system to fail.

If the brake fluid level drops below the

MIN

marking, the brake system is leaking or the brake linings are worn down.

–

Check the brake system and do not continue riding until the problem is eliminated. (Your authorized Husqvarna Motorcycles

workshop will be glad to help.)

Содержание 701 Enduro 2017

























































































































































































































Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды

Husqvarna 701 Enduro 2017, Руководство пользователя

Результаты поиска

Содержание 701 Enduro 2017

Отзывы:

Похожие инструкции для 701 Enduro 2017

Бренды по названию

Популярные бренды