Husqvarna 5524 STE Скачать руководство пользователя | Manualshive

Страница: 25 / 32

background image

25

REPAIR PARTS

HANDLES

SNOW THROWER - MODEL NO.

5224STE

(96193001400), PRODUCT NO. 961 93 00-14

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

KEY PART
NO. NO.

DESCRIPTION

   1   532 40 76-49   Lever, Auger Control, RH
   2   532 40 76-48   Lever, Traction Drive Control, LH
   4   532 17 88-88   Bushing, Flange
   5   532 16 96-75   Retainer, Hairpin
   6   817 06 04-08   Screw, Hex Head
   7   532 17 86-52   Rod, Interlock
   8   532 19 95-76   Arm, Impeller Rod
   9   532 19 95-75   Arm, Traction Rod

10 532 19 95-31 Panel, Control

11 874 78 05-24 Screw, Hex Head 5/16-18 x 1-1/2

12   874 78 05-12   Screw, Hex Head 5/16-18 x 1-3/4
13   532 40 78-36   Handle Tube, LH
14   532 40 78-35   Handle Tube, RH
15   532 75 11-53 Nut, Lock 5/16-18
16   819 13 13-16   Washer, Flat 3/8
17   532 17 88-99   Knob, Handle
18   532 18 04-80   Rod, Auger Control
19   532 18 04-81   Rod, Traction Control
22   872 12 06-18   Bolt, Carriage 3/8-16 x 2-1/4
23   532 18 40-87   Handle Tube, Lower
24   532 18 04-47   Sleeve, Spring
25   532 18 09-26   Spring, Traction Drive
26   532 17 86-69   Spring, Auger Control
27   817 00 06-16   Screw, Hex Head 3/8-16 x 1
28   532 19 85-59   Bushing, Pivot Lever
30   532 18 33-52   Console, Panel
31   532 17 52-62   Screw, Hex Head, Tapping #10-24 x 1-1/4
32   532 18 44-71   Screw, Hex Head, Tapping #10-24 x 1/2
36   532 17 88-31   Spring, Torsion
47   532 19 69-43   Mounting Bracket, Handle, LH
48   532 19 69-44   Mounting Bracket, Handle, RH
49   532 19 95-13   Grip, Handle

«
...
23
24
25
26
27
...
»

Содержание 5524 STE

































Отзывы:

Нет отзывов

Похожие инструкции для 5524 STE

Бренд: Makita Страницы: 84

Бренд: Makita Страницы: 35

Бренд: Makita Страницы: 6

Бренд: Makita Страницы: 6

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 148

Бренд: Makita Страницы: 66

Бренд: Makita Страницы: 8

Бренд: Makita Страницы: 9

Бренд: Zenoah Страницы: 15

Бренд: Nilfisk-Advance Страницы: 38

SNOW ELECTRIC 45

Бренд: Stiga Страницы: 81

Бренд: Simplicity Страницы: 26

Бренд: Sartorius Страницы: 2

HELIFLOW HYCL BA

Бренд: Gardner Denver Страницы: 40

Бренд: Yardworks Страницы: 14

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды