Husqvarna 525 LX Скачать руководство пользователя страница 8

Страница: 8 / 32

decreases the vibration that goes between the engine

unit and the shaft unit of the product.

1. Stop the engine.
2. Do a visual check for deformation and damage. For

example, cracks.

3. Make sure you attach the elements of the vibration

damping system correctly.

To do a check of the muffler

WARNING: Do not use a product that has a

defective muffler. Always replace a defective

muffler. .

CAUTION: The spark arrester screen must

be replaced if it is damaged. Do not use the

product if the spark arrester screen on the

muffler is missing or defective.

CAUTION: The muffler becomes too hot if

the spark arrester screen is blocked. A too

hot muffler causes damage to the cylinder

and piston.

1. Make sure that the muffler is not damaged.

2. Make sure that the muffler is correctly attached to

the product.

3. If the muffler on your product has a spark arrester

screen, do a visual check.

4. If maintenance is necessary, refer to

To do

maintenance on the muffler on page 15

Fuel Safety

WARNING: Read the warning instructions

that follow before you use the product.

• Never start the product if you spill fuel on it. Wipe the

spillage of and allow remaining fuel to evaporate.

• Never start the product if you spill fuel on yourself or

your clothes. Change your clothes and wash any

part of your body that has come in contact with fuel.

Use soap and water.

• Never start the product if the product is leaking fuel.

Check regularly for leaks from the fuel cap and fuel

lines.

• Always put the product on a flat surface and make

sure the cutting attachment cannot come in contact

with any object while you add fuel.

• Take care when handling fuel. Bear in mind the risk

off fire, explosion and inhaling fumes.

• Observe caution when handling fuel and make sure

there is adequate ventilation. Fuel and fuel fumes

are highly inflammable and can cause serious injury

when inhaled or allowed to come in contact with the

skin.

• Mix and pour fuel outdoors, where there are no

sparks or flames.

• Do not smoke or place hot objects near fuel.
• Always stop the engine and let it cool off for a few

minutes before you refuel.

• Open the fuel cap slowly so that any excess

pressure is released gently when you refuel.

• Tighten the fuel cap carefully after you refueled.
• Clean the area around the fuel cap. Contamination in

the tank can cause operating problems.

• Always move the product 3m (10ft) or further from

the refuelling area and source before starting.

1003 - 001 - 07.01.2019

Содержание 525 LX

































Результаты поиска

Содержание 525 LX

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna 525 LX, Руководство оператора

Результаты поиска

Содержание 525 LX

Отзывы:

Бренды по названию

Популярные бренды