manualshive.com logo in svg

Husqvarna 525 LX, Руководство оператора

Поделиться
Скачать
Husqvarna 525 LX Скачать руководство пользователя страница 16

dirty or blocked cooling system makes the product too

hot which causes damage to the piston and cylinder.
The components of the cooling system:
(A) Cylinder cover (directs cool air over the cylinder).
(B) Cooling fins on the flywheel.
(C) Muffler cover.
(D) Muffler plate.
(E) Air intake on the starter.
(F) Cooling fins on the cylinder.

A

B

C

E

F

D

To examine the spark plug

CAUTION: Always use the recommended

spark plug type. Incorrect spark plug type

can cause damage to the product.

• Examine the spark plug if the engine is low on

power, is not easy to start or does not operate

correctly at idle speed.

• To decrease the risk of unwanted material on the

spark plug electrodes, obey these instructions:
a) Make sure that the idle speed is correctly

adjusted.

b) Make sure that the fuel mixture is correct.
c) Make sure that the air filter is clean.

• If the spark plug is dirty, clean it and make sure that

the electrode gap is correct, refer to 

Technical data

on page 18

.

• Replace the spark plug if it is necessary.

Air filter

Remove dust and dirt from the air filter to keep it clean in

order to prevent:
• Carburettor malfunctions.
• Starting problems.
• Loss of engine power.
• Unnecessary wear to engine parts.
• Too much fuel consumption.
Clean the air filter at an interval of 25 hours, or more

regularly if conditions are unusually dusty.

To clean the air filter

CAUTION: Always replace an air filter that is

damaged, very dirty or soaked with fuel.

If you use an air filter for a long time, it cannot be fully

cleaned. Replace the air filter with a new one at regular

intervals.
1. Move the choke lever up, to close the choke valve.

2. Remove the air filter cover.

3. Remove the felt filter and the air filter.
4. Use air or a brush to clean the felt filter.
5. Do a check of the surface of the rubber seal.

Replace the filter on the rubber seal if it is damaged.

6. Clean the air filter with warm soap water.

16

1003 - 001 - 07.01.2019

Содержание 525 LX

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды