Husqvarna 525 LST Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 36

background image

To clean the air filter

CAUTION: A air filter that is damaged, very

dirty or soaked with fuel must always be

replaced.

If you use an air filter for a long time it cannot be fully

cleaned. Replace the air filter with a new one at regular

intervals.
1. Move the choke lever up, to close the choke valve.

2. Remove the air filter cover and remove the air filter.

3. Clean the air filter with warm soap water.
4. Replace the air filter if it is too dirty to fully clean it.

Always replace a damaged air filter.

5. Also clean the inner surface of the filter cover. Use

air or a brush.

6. Do a check of the rubber sealing surface. Replace

the filter on the rubber seal if it is damaged.

7. Make sure that the filter is dry before you assemble

it.

Bevel gear

The bevel gear is filled with the right quantity of grease

at the factory. But, before you use the product, make

sure that the bevel gear is 3/4 full with grease. Use

Husqvarna special grease.

The grease in the bevel gear does not need to be

changed unless repairs are carried out.

Two piece-shaft (525RJD)

• Apply grease to the end of the drive shaft after each

30 hours of operation.

Troubleshooting

The engine does not start

Check

Possible cause

Procedure

Stop switch.

The stop switch is in the stop position.

Set the stop switch to the start position.

Starter pawls.

The starter pawls cannot move freely.

Remove the starter cover and clean around

the starter pawls.

Let an approved service agent help you.

1363 - 001 - 25.10.2019

23

«
...
21
22
23
24
25
...
»

Содержание 525 LST





































Отзывы:

Нет отзывов

Похожие инструкции для 525 LST

Бренд: Yard Machines Страницы: 64

Бренд: Weed Eater Страницы: 7

Бренд: Shindaiwa Страницы: 24

TrimLite UT20740

Бренд: Homelite Страницы: 24

Бренд: LawnMaster Страницы: 28

Swingline ClassicCut lite 9312

Бренд: ACCO Brands Страницы: 2

Бренд: Black & Decker Страницы: 40

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 64

Бренд: Black & Decker Страницы: 22

Бренд: Black & Decker Страницы: 50

Бренд: Black & Decker Страницы: 44

Бренд: Black & Decker Страницы: 12

Бренд: Black & Decker Страницы: 80

Бренд: Black & Decker Страницы: 32

Hedge Hog HS1010

Бренд: Black & Decker Страницы: 5

HTD22SW Hedge Hog XB

Бренд: Black & Decker Страницы: 5

Бренд: Black & Decker Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды