background image

Contents

Introduction..................................................................... 2

Safety..............................................................................4

Assembly...................................................................... 10

Operation...................................................................... 15

Maintenance................................................................. 19

Troubleshooting............................................................ 23

Transportation, storage and disposal........................... 24

Technical data.............................................................. 25

Accessories.................................................................. 26

Introduction

Product description

The product is a grass trimmer with a combustion

engine.
Work is constantly in progress to increase your safety

and efficiency during operation. Speak to your servicing

dealer for more information.

Intended use

The product is used with a trimmer head to cut grass.

Do not use the product for other tasks than grass

trimming and grass clearing.

Note: National regulations can set limit to the operation

of the product.

Product overview

17

18

24

25

19

4

35

26

23

11

10

12

14

13

32

8

31

7

9

30

34

29

28

15

7

8

37

6

28

32

20

36

22

27

21

33

5

4

3

2

1

16

9

1. Trimmer head
2. Grease filler cap
3. Bevel gear
4. Cutting attachment guard

5. Shaft
6. Loop handle (525LST, 525RJD)
7. Throttle trigger
8. Stop switch

2

1363 - 001 - 25.10.2019

Содержание 525 LST





































Отзывы: