background image

 

GENERAL SAFETY PRECA

 

UTIONS

 

8

 

 – 

 

English

 

Al

 

ways use common sense

 

It is not possib

 

le to cover every conceivable situation you 

can face when using a chain saw. Always exercise care 
and use your common sense. Avoid all situations which 
you consider to be beyond your capability.  If you still feel 
uncertain about operating procedures after reading these 
instructions, you should consult an expert before 
continuing. Do not hesitate to contact your dealer or us if 
you have any questions about the use of the chain saw. 
We will willingly be of service and provide you with advice 
as well as help you to use your chain saw both efficiently 
and safely. Attend a training course in chain saw usage if 
possible. Your dealer, forestry school or your library can 
provide information about which training materials and 
courses are available.

 Work is constantly in progress to improve the design and 
technology - improvements that increase your safety and 
efficiency. Visit your dealer regularly to see whether you 
can benefit from new features that have been introduced.

 

P

 

ersonal protective equipment

 

 

Approved protective helmet

Hearing protection

Protective goggles or a visor

Gloves with saw protection

Trousers with saw protection

Boots with saw protection, steel toe-cap and non-slip 
sole

Always have a first aid kit nearby.

Fire Extinguisher and Shovel

Generally clothes should be close-fitting without 
restricting your freedom of movement.

 

Machine

′′′′

s safety equipment

In this section the machine’s safety features and their 
function are explained. For inspection and maintenance 
see instructions under the heading Checking, maintaining 
and servicing chain saw safety equipment. See 
instructions under the heading, What is what?, to find 
where these parts are located on your machine.

The life span of the machine can be reduced and the risk 
of accidents can increase if machine maintenance is not 
carried out correctly and if service and/or repairs are not 
carried out professionally. If you need further information 
please contact your nearest servicing dealer.

Chain brake and front hand guard

Your chain saw is equipped with a chain brake that is 
designed to stop the chain if you get a kickback. The chain 
brake reduces the risk of accidents, but only you can 
prevent them.

!

WARNING! Most chain saw accidents 
happen when the chain touches the 
operator. You must use approved 
personal protective equipment whenever 
you use the machine. Personal protective 
equipment cannot eliminate the risk of 
injury but it will reduce the degree of 
injury if an accident does happen. Ask 
your dealer for help in choosing the right 
equipment.

IMPORTANT! Sparks can come from the muffler, the bar 
and chain or other sources. Always have fire 
extinguishing tools available if you should need them. 
Help prevent forest fires.

!

WARNING! Never use a machine with 
defective safety components. Safety 
equipment must be inspected and 
maintained. See instructions under the 
heading Checking, maintaining and 
servicing chain saw safety equipment. If 
your machine does not pass all the 
checks, take the saw to a servicing 
dealer for repair.

Содержание 346XP TrioBrake

















































Отзывы: