background image

English

 – 21

TECHNICAL DATA

Technical data

Note 1: Noise emissions in the environment measured as sound power (L

WA

) in conformity with EC directive 2000/14/EC.

Note 2: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various 
working conditions with the following time distribution: 1/2 idling and 1/2 max speed.

NOTE!   The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting 
attachments for the machine. The table indicates the lowest  and highest values.

Technical data

326Lx

Engine

Cylinder displacement, cm

3

24,5

Cylinder bore, mm

34,0

Stroke, mm

27

Idle speed, rpm

2700

Recommended max. fast idle speed, rpm

11000-11700

Speed of output shaft, rpm

8014

Max. engine output, acc. to ISO 8893, kW/ rpm

0,9/8400

Catalytic converter muf

fl

er

Yes

Speed-regulated ignition system

No

Ignition system

Manufacturer/type of ignition system

WalbroMB/SEM AM49

Spark plug

Champion RCJ 6Y

Electrode gap, mm

0,5

Fuel and lubrication system

Manufacturer/type of carburettor

Zama C1Q

Fuel tank capacity, litre

0,5

Weight

Weight without fuel, cutting attachment and guard, kg

4,4

Noise emissions

(see note 1)

Sound power level, measured dB(A)

106

Sound power level, guaranteed L

WA

 dB(A)

106

Noise levels

(see note 2)

Equivalent noise pressure level at the operator’s ear, 
measured according to EN/ISO 11806 and ISO 7917, dB(A), 
min./max.:

91/97

Vibration levels

Vibration levels at handles, measured according to EN/ISO 
11806 and ISO 7916, m/s

2

At idle, left/right handles, min.:

1,7/1,5

At idle, left/right handles, max.:

2,7/1,8

At max. speed, left/right handles, min.:

3,9/5,2

At max. speed, left/right handles, max.:

7,2/9,8

Approved accessories

Type

Cutting attachment guard, Art. no.

Blade shaft thread M10

Plastic blades

Tricut Ø 300 mm

503 93 42-02

Trimmer head

Trimmy Fix

503 93 42-02 /  503 97 71-01

Superauto II 1"

503 93 42-02 /  503 97 71-01

S35

503 93 42-02 /  503 97 71-01

T35

503 93 42-02 /  503 97 71-01

Attachments

Saw attachment without shaft PA

537 18 33-11

Содержание 326LX SERIES





























Отзывы: