Husqvarna 323R series Скачать руководство пользователя | Manualshive

Страница: 9 / 44

background image

English –

9

7. Quick-release

• Check that the harness

straps are correctly
positioned. When the
harness and machine are
adjusted, check the harness‘
safety release catch to
ensure it works correctly.

SAFETY INSTRUCTIONS

6. Cutting equipment

This section describes how through correct maintenance and
through using the right type of cutting equipment you can:
• Reduce the machine‘s tendency to kickback
• Obtain maximum cutting capacity.
• Increase the service life of the cutting equipment.

Four basic rules:

1)Only use the cutting

and guard equipment
we recommend! See
chapter “Technical
data“.

2)Keep the blade‘s teeth

well and correctly
sharpened! Follow our
instructions and use the
recommended filing
gauge. An incorrectly
sharpened or damaged
blade increases the risk
of an accident.

3)Keep the correct setting.

Follow our instructions
and use the
recommended setting
tool. An incorrectly set
blade increases the risk
of jamming and
kickback.

4)Check the cutting

equipment with regard
to damage and crack
formation. Damaged
cutting equipment
should always be
replaced.

!

WARNING!
Never use a machine with defective
safety equipment. The safety equipment
should be maintained as described in this
section. If your machine does not meet
any of these controls you should contact
your service workshop.

8. Locking nut

• Protect your hand from

injury when assembling,
use the blade guard as
protection when tightening
with a socket spanner.
Tighten the nut by turning
against the direction of
rotation. Loosen the nut by
turning in the direction of
rotation. (NOTE! the nut
has a left-hand thread).

• Tighten the nut using a

socket spanner, 35 - 50
Nm (3.5 - 5 kpm).

NOTE!

The locking nut‘s nylon lock
must not be so worn that it
can be turned by hand. The
lock shall hold at least 1.5
Nm. The nut should be
replaced after it has been put
on approx. 10 times.

«
...
7
8
9
10
11
...
»

Содержание 323R series













































Отзывы:

Нет отзывов

Похожие инструкции для 323R series

Бренд: SPEWE Страницы: 10

Бренд: D-CUT Страницы: 4

Бренд: Ryobi Страницы: 17

Бренд: Festool Страницы: 141

Бренд: XPOtool Страницы: 4

Dolphin Generation 2 XP-005L

Бренд: Xhorse Страницы: 9

Auto-Cutter CL-S6621

Бренд: Citizen Страницы: 16

Бренд: Metabo HPT Страницы: 40

Бренд: Circut Страницы: 4

Бренд: Aosome Страницы: 29

DUALBLADEROOFCUTTER

Бренд: Panther Страницы: 17

Бренд: Ilco Orion Страницы: 26

Бренд: Maruyama Страницы: 38

Бренд: Stiga Страницы: 318

Бренд: Poulan Pro Страницы: 64

Бренд: US Cutter Страницы: 50

Бренд: Rothenberger Industrial Страницы: 76

Бренд: TASKMASTER TOOLS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды