Husqvarna 242XP Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 36

background image

English –

11

!

SAFETY INSTRUCTIONS

C

Some terms that describe the bar and chain

When the cutting equipment supplied with your saw becomes
worn or damaged you will need to replace it. Use only the type
of bar and chain recommended by us. See the

”Technical data”

section to find out which equipment is recommended for your
saw.

Bar

• LENGTH (inches/cm)

• NUMBER OF TEETH ON

BAR TIP SPROCKET (T).
Small number = small tip
radius = low-kickback

• CHAIN PITCH (inches)

The spacing between the
drive links of the chain must
match the spacing of the
teeth on the bar tip sprocket
and drive sprocket.

• NUMBER OF DRIVE LINKS

The number of drive links is
determined by the length of
the bar, the chain pitch and
the number of teeth on the
bar tip sprocket.

• BAR GROOVE WIDTH

(inches/mm)
The groove in the bar must
match the width of the chain
drive links.

• SAW CHAIN OIL HOLE

AND HOLE FOR CHAIN
TENSIONER
The bar must be matched to
the chain saw design.

Saw chain

• SAW CHAIN PITCH

(inches)
Spacing between drive
links.

• DRIVE LINK WIDTH (mm/

inches)

• NUMBER OF DRIVE LINKS

• LEVEL OF KICKBACK

REDUCTION
The level of kickback
reduction offered by a chain
is indicated by its model
number.
See the

”Technical data”

section to find the model
numbers of chains that are
recommended for use with
your saw.

1 Cutting equipment designed to minimise

kickback

Faulty cutting equipment or the wrong
combination of bar and chain increases the
risk of kickback. Use only the bar and chain
combinations recommended in the

”Technical

data” section.

The only way to avoid kickback is to make sure that the kick-
back zone of the bar never touches anything.
By using cutting equipment with “built-in” kickback protection
and keeping the chain sharp and well-maintained you can
reduce the effects of kickback.

A

Bar

The smaller the tip radius the
smaller the kickback zone and
the lower the chance of
kickback.

B

Saw chain

A saw chain is made up of a number of links, which are
available in standard and low-kickback versions.

None

Standard

Low-kickback

CUTTING LINK

DRIVE LINK

SIDE LINK

Combining these links in different ways gives different degrees
of kickback reduction. In terms of kickback reduction alone, four
different types of link are available.

Kickback reduction

Cutting link

Drive link

Side link

LOW

STANDARD

HIGH

EXTRA HIGH

«
...
9
10
11
12
13
...
»

Содержание 242XP





































Отзывы:

Нет отзывов

Похожие инструкции для 242XP

Power X Change PXCCSS-0182

Бренд: Ozito Страницы: 12

Бренд: Nakayama Страницы: 64

Бренд: GreenWorks Pro Страницы: 13

Бренд: ATIKA Страницы: 134

Бренд: Poulan Pro Страницы: 21

20 Volt Max HT19-401-003-11

Бренд: Hyper Tough Страницы: 2

HT19-401-003-11

Бренд: Hyper Tough Страницы: 2

Бренд: YATO Страницы: 120

Бренд: Ryobi Страницы: 120

Бренд: Tanaka Страницы: 15

Бренд: GARDEO PRO Страницы: 139

YELLOW GARDENLINE YGL N.G. 5351

Бренд: Zgonc Страницы: 48

CS-400 - PARTS CATALOG SERIAL NUMBER C09212001001 -...

Бренд: Echo Страницы: 34

Бренд: Makita Страницы: 44

Бренд: Makita Страницы: 24

Бренд: Deltafox Страницы: 208

Бренд: GreenWorks Pro Страницы: 15

Бренд: Husqvarna Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды