manualshive.com logo in svg

Husqvarna 240RBD, Руководство оператора, Страница: 22 / 41

Поделиться
Скачать
Husqvarna 240RBD Скачать руководство пользователя страница 22

22

 – English

MAINTENANCE

Drive shaft

The flexible drive shaft is lubricated with special grease. The
shaft must be lubricated at least every 25 working hours. A
tube of drive shaft grease is supplied with every machine.
NOTE! Do not use gearbox grease on the drive shaft.

B

A

• Separate the two rig shaft halves (see page 16).

• Remove the bolt that

holds the drive shaft
sleeve in the clutch cover.

• Remove the clip that

holds the throttle cable on
the drive shaft.

• Pull the drive shaft sleeve

out of the clutch cover.

• Remove the drive shaft

from the sleeve either by
shaking it out or pulling it
out using pliers.

• Coat the surface of the

shaft with grease from the
tube. Spread it out using a
brush or rag.

• Slide the drive shaft back

into the sleeve. Make sure
the shaft engages correctly
by turning it and pushing
at the same time.

• When the shaft is correctly

installed in the sleeve the
end of the shaft should
project about 30 mm
beyond the edge of the
sleeve.

• When the sleeve and drive

shaft are installed in the
clutch cover the guide pin
(A) on the sleeve and the
adjustable stop (B) must
be positioned opposite
each other.

• Rotate the shaft and push

it in at the same time.

• Install the drive shaft

sleeve in the clutch cover
so that the stop locates in
the slot on the underside
of the clutch cover.

• Tighten the locking bolt.

NOTE! The bolt must be
inserted in the threaded
half of the cover first, so
that the cover is not drawn
together.

Содержание 240RBD










































Отзывы:

Нет отзывов