manualshive.com logo in svg

Husqvarna 240RBD, Руководство оператора, Страница: 18 / 41

Поделиться
Скачать
Husqvarna 240RBD Скачать руководство пользователя страница 18

18

 – English

START AND STOP

Control before starting

Cold engine

IGNITION: Set the stop
switch to the start position.
CHOKE:  Set the choke
control in the choke position.
AIR PURGE:Press the air
purge diaphragm repeatedly
until fuel begins to fill the
diaphragm. The diaphragm
need not be completely filled

Warm engine

Use the same starting
procedure as for the cold
engine, but do not set the
choke control in the choke
position. The start throttle
position is obtained by setting
the choke control in the
choke position and then
returning it to its original
position.

Stop

The engine is stopped by
switching off the ignition.

"

For reasons of safety follow
these recommendations!

• Check the blade to ensure

that no cracks have formed
at the bottom of the teeth
or by the centre hole. The
most common reason why
cracks are formed is that
sharp corners have been
formed at the bottom of
the teeth while sharpening
or that the blade has been
used with dull teeth.
Discard a blade if cracks
are found.

• Check that the support

flange is not cracked due
to fatigue or due to being
tightened too much.
Discard the support flange
if it is cracked.

• Ensure the locking nut has

not lost its captive force.
The nut lock should have a
locking force of at least 1.5
Nm. The tightening
torque of the locking nut
should be 35-50 Nm.

• Check that the guard is

not damaged or cracked.
Replace the guard if it is
exposed to impact or is
cracked.

• Check that the trimmer

head and spray guard are
not damaged or cracked.
Replace the trimmer head
or spray guard if they are
exposed to impact or are
cracked.

• Never use the machine without a guard or spray guard nor

with a defective guard.

Start and stop

!

WARNING!
The complete clutch cover with shaft
must be fitted before the machine is
started, otherwise the clutch can become
loose and cause personal injury.
Always move the machine from the filling
area before starting. Place the machine on
a flat surface. Ensure the cutting
equipment cannot come into contact with
any object. Make sure no unauthorised
persons are in the working area,
otherwise there is a risk of serious
personal injury. The safety distance is 15
metres.

!

WARNING!
When the engine is started with the choke
in the choke or start position the cutting
equipment starts to rotate immediately.

Start

Press the machine body
against the ground using
your left hand (NOTE! Not
your foot). Grip the starter
handle, slowly pull out the
cord with your right hand
until you feel some resistance
(the starter pawls grip), now
quickly and powerfully pull
the cord.
Reset the choke control as
soon as the engine fires and
repeat until the engine starts.
When the engine starts
quickly apply full throttle
and the start throttle will
automatically disengage.
NOTE! Do not pull the
starter cord out completely
and do not release the starter
cord from the fully extended
position. This can damage
the machine.

Содержание 240RBD










































Отзывы:

Нет отзывов