Husqvarna 2016 FE 250 Скачать руководство пользователя страница 55

Страница: 55 / 124

12 SERVICE WORK ON THE CHASSIS

B01814-11

Main work

–

Disconnect spring



Spring hook (50305017000)

–

Remove screws



and take off the main silencer.

12.29

Installing the main silencer

H00246-11

Main work

–

Mount the main silencer. Mount screws



but do not tighten yet.

–

Reconnect spring



Spring hook (50305017000)

–

Tighten screws



Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

Finishing work

–

Install the right side cover. (

p. 52)

12.30

Cleaning the spark arrestor (FE US)

Warning

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

–

Allow the exhaust system to cool down. Do not touch hot components.

Info

Soot particles accumulate on the screen of the spark arrestor over time.
This changes the performance characteristics.

Preparatory work

–

Remove the right side cover. (

p. 52)

–

Remove the main silencer. (

p. 52)

Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды