Husqvarna 2016 FE 250 Скачать руководство пользователя страница 54

Страница: 54 / 124

12 SERVICE WORK ON THE CHASSIS

–

Check the intake flange for damage and looseness.

Finishing work

–

Install the air filter.

(

p. 51)

–

Install the air filter box lid. (

p. 50)

12.25

Sealing the air filter box

Preparatory work

–

Remove the air filter box lid. (

p. 50)

401559-01

Main work

–

Seal the air filter box in the marked area



Finishing work

–

Install the air filter box lid. (

p. 50)

12.26

Removing the right side cover

H00186-10

–

Remove screw



–

Pull off the side cover in area



sideways and remove it toward the rear.

12.27

Installing the right side cover

H00186-10

–

Position the side cover and engage in area



–

Mount and tighten screw



Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

12.28

Removing the main silencer

Warning

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

–

Allow the exhaust system to cool down. Do not touch hot components.

Preparatory work

–

Remove the right side cover. (

p. 52)

Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Бренды по названию

Популярные бренды