Husqvarna 2016 FE 250 Скачать руководство пользователя страница 52

Страница: 52 / 124

12 SERVICE WORK ON THE CHASSIS

12.19

Mounting the seat

H00183-10

–

Mount the front of the seat on the collar bushing of the fuel tank, lower the seat at

the rear, and simultaneously push the seat forward.

The seat is correctly engaged.

H00182-10

–

Mount and tighten seat fixing screws



Guideline

Remaining screws, chassis

10 Nm (7.4 lbf ft)

12.20

Removing the air filter box lid

H00213-10

–

Release catch



, pull off the air filter box lid sideways in areas



and



and

remove toward the rear.

12.21

Installing the air filter box lid

H00213-10

–

Position the air filter box lid and tab



. Engage the air filter box lid in areas



and



–

Engage tab



12.22

Removing the air filter

Note

Engine failure

Unfiltered intake air has a negative effect on the service life of the engine.

–

Never operate the vehicle without an air filter as dust and dirt will enter the engine and lead to increased wear.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Preparatory work

–

Remove the air filter box lid. (

p. 50)

Содержание 2016 FE 250





























































































































Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды

Husqvarna 2016 FE 250, Руководство пользователя

Результаты поиска

Содержание 2016 FE 250

Отзывы:

Похожие инструкции для 2016 FE 250

Бренды по названию

Популярные бренды