Husqvarna 1830EXLT Скачать руководство пользователя страница 7

Страница: 7 / 28

ASSEMBLY / PRE-OPERATION

INSTALL TRACTION DRIVE CONTROL ROD

(See Figs. 3 and 4)

The traction drive control rod is installed on the snow

thrower.
1. Remove plastic tie securing rod to lower handle.
2. With top end of rod positioned under left side of control

panel, push rod down and insert top end of rod into hole

in drive control bracket. Secure with retainer spring.

TRACTION

DRIVE

CON TROL

ROD

DRIVE

CONTROL

BRACKET

RETAINER

SPRING

TRACTION DRIVE

CON TROL LEVER

FIG. 4

AUGER

CONTROL

LEVER

AUGER CONTROL ROD

AUGER

CONTROL

BRACKET

RETAINER

SPRING

FIG. 6

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1. Retrieve vinyl sleeve and spring from bag of parts and

retrieve the auger control rod from carton chute tray.

Slide straight rod end through the small hole in the

vinyl sleeve. Using the long hook end of the spring,

hook spring in hole #4 in rod.

(See Fig. 5).

2. Hook end of spring into control arm with loop opening

up as shown. (See Fig. 5).

3. With top end of rod positioned under right side of control

panel, push down on rod and insert end of rod into hole

in auger control bracket. Secure with retainer spring.

FIG. 5

AUGER

CONTROL

ROD

CONTROL

ARM

VINYL

SLEEVE

LOOP

OPENING

TRACTION DRIVE

CONTROL ROD

VINYL

SLEEVE

FIG. 3

PLASTIC TIE

Содержание 1830EXLT





























Результаты поиска

Содержание 1830EXLT

Отзывы:

Похожие инструкции для 1830EXLT

Бренды по названию

Популярные бренды

Husqvarna 1830EXLT, Руководство оператора

Результаты поиска

Содержание 1830EXLT

Отзывы:

Похожие инструкции для 1830EXLT

Бренды по названию

Популярные бренды