Husqvarna 1827EXLT Скачать руководство пользователя

Страница: 10 / 28

FUEL SHUT-OFF VALVE

ON / OFF

SWITCH

MUF FLER

GAS O LINE

FILLER CAP

SAFETY

IGNITION

KEY

CHOKE

CON-

TROL

PRIM ER

RECOIL (AUXILIARY) STARTER HANDLE

ELECTRIC

START

BUTTON

POWER

CORD

PLUG

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

FIG. 10

OPERATION

Drive speed control lever -

used to select forward or

reverse motion and speed of snow thrower.

Traction drive control lever -

used to engage power-pro-

pelled for ward or reverse motion of snow thrower.

Auger control lever -

used to engage auger motion (throw

snow).

Discharge chute control lever -

used to change the di rec-

tion the snow is thrown.

Deflector remote control lever -

used to change the

dis tance the snow is thrown.

Skid plate -

used to adjust height of scraper bar from the

ground.

Drift cutter -

used to cut through deep snowdrifts.

Toolbox -

used to store spare shear bolts, locknuts and

wrench.

Freewheel control

–

disengages transmission for pushing

the snowthrower with the engine off.

Safety ignition key -

must be inserted for the engine to

start and run. Remove when snow thrower is not in use.

Electric start button -

used for starting the engine.

Recoil (auxiliary) starter handle -

used for start ing en gine.

Primer -

pumps additional fuel from the carburetor to the

cylinder for use when starting a cold engine.

Choke Control -

used for starting a cold engine.

ON / OFF switch -

used to STOP the engine.

LH and RH turn triggers -

used to steer the snow thrower.

DEFLECTOR

REMOTE

CONTROL LEVER

TRACTION

DRIVE

CONTROL

LEVER

DISCHARGE CHUTE CONTROL LEVER

DRIVE SPEED

CON TROL LEVER

AUGER

CONTROL

LEVER

MUF FLER

TOOLBOX

HANDLE

KNOB

SKID PLATE

CHUTE

DE FLEC TOR

DISCHARGE

CHUTE

AU GERS

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

LIGHT

LH TURN

TRIGGER

CLEAN-OUT TOOL

DRIFT

CUTTER

Содержание 1827EXLT





























Результаты поиска

Содержание 1827EXLT

Отзывы:

Похожие инструкции для 1827EXLT

Бренды по названию

Популярные бренды

Husqvarna 1827EXLT, Руководство оператора

Результаты поиска

Содержание 1827EXLT

Отзывы:

Похожие инструкции для 1827EXLT

Бренды по названию

Популярные бренды