BATTERY HAND
LI
NG
English
–
13
Battery status
The display shows the battery capacity and if there are
any problems with the battery. The battery capacity is
displayed for
5
seconds after the machine is switched off
or the battery indicator button (
1
) is pressed. The warning
symbol on the battery is lit when an error has occurred
(
2
). See fault codes. (Figure
26
)
Battery charger
C
onnect the battery charger
•
Connect the battery charger to the voltage and
frequency specified on the rating plate. Put the
electric plug in a earthed socket-outlet.
•
The battery will not be charged if the battery
temperature is over
50
°
C (
122
°
F).
C
onnect the battery to the battery charger
Regularly check that the battery charger and the battery
are intact. See also instructions under the heading
Maintenance.
The battery must be charged before using it the first time.
The battery is only
30
% charged when delivered.
•
Connect the battery to the battery charger
(Figure
14
)
•
The green charging light on the charger is lit when the
battery is connected to the battery charger. The
charging process is ongoing.
(Figure
13
)
•
When all the LEDs are lit on the battery, it is fully
charged.
(Figure
12
)
•
Pull out the plug. Never jerk the power supply cable to
disconnect it from the wall socket.
•
Disconnect the charger from the battery.
C
harging status
Lithium-ion batteries can be charged at whatever
charging level. The charging process can be cancelled or
started whatever the battery’s charge level is. A fully
charged battery will not lose its charge even when the
battery is left in the charger.
(Figure
27
)
Transport and storage
•
The contained lithium-ion batteries are subject to the
Dangerous Goods Legislation requirements.
•
For commercial transports e.g. by third parties,
forwarding agents, special requirement on packing
and labeling must be observed.
•
For preparation of the item being shipped, consulting
an expert for hazardous material is required. Please
also observe possibly more detailed national
regulations.
•
Tape or mask off open contacts and pack up the
batteriy in such a manner that it cannot move around
in the packing.
•
Always remove the battery for storage or transport.
•
Store the battery and the battery charger in a dry,
moisture-free and frost-free space.
•
Do not store the battery in places where static
electricity can occur. Never store the battery in a metal
box.
•
Store the battery and the battery charger where the
temperature is between
5
°
C (
41
°
F) and
45
°
C (
113
°
F) and never in direct sunlight.
•
Store the battery charger only in an enclosed and dry
space.
•
Be sure to store the battery separate from the battery
charger. Store the equipment in a lockable area so
that it is out of reach of children and unauthorized
persons.
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
•
The transport guard must always be fitted to the
cutting attachment when the machine is being
transported or in storage.
•
Secure the machine during transport.
L
ED lights
Battery status
All LEDs are lit
Fully charged (
75
-
100
%).
LED
1
, LED
2
, LED
3
are lit.
The battery is
50
%-
75
%
charged.
LED
1
, LED
2
are lit.
The battery is
25
%-
50
%
charged.
LED
1
is lit.
The battery is
0
%-
25
%
charged.
LED
1
flashes.
The battery is empty.
Charge the battery.
!
WARN
I
NG
!
Risk of electric shock and
short circuiting. Use approved and intact
wall sockets. Make sure that the cable is
not damaged. Replace cable if it appears
to be damaged in any way.
L
ED display
C
harging status
LED
1
flashes.
The battery is
0
%-
25
% charged.
LED
1
is lit, LED
2
flashes.
The battery is
25
%-
50
% charged.
LED
1
, LED
2
are lit, LED
3
flashes.
The battery is
50
%-
75
% charged.
LED
1
, LED
2
, LED
3
are lit, LED
4
flashes.
Battery is
75
%-
100
% charged
LED
1
, LED
2
, LED
3
, LED
4
are lit.
When all the LEDs
are lit on the battery,
it is fully charged.
