Husqvarna Viking Mega Quilter Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 44

background image

9

A

B

C

Electrical connection

Before connecting to the power supply, make

sure the voltage shown on the machine conforms to
your electrical power. Always turn the power off
and unplug the sewing machine from the electrical
outlet when the machine is not in use.

Connect the power cord between the socket
of the MEGA QUILTER™ (A) and the
wall outlet.

For the USA and Canada:

This sewing machine has a polarized
plug (one blade wider than the other). To
reduce the risk of  electric shock, this plug
is intended to fit in a polarized outlet only
one way. If  the plug does not fit fully in the
outlet, reverse the plug. If  it still does not
fit, contact a qualified electrician to install
the proper outlet.

DO NOT modify the plug in any way!

Connecting the foot control

Switch off the main switch

.

Connect the plug of the foot control (B)
to the connection socket of the MEGA
QUILTER™.
Turn on the power switch (C).

Operating your MEGA QUILTER™

«
...
9
10
11
12
13
...
»

Содержание Mega Quilter













































Отзывы:

Нет отзывов

Похожие инструкции для Mega Quilter

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 60

Бренд: Westomatic Страницы: 41

Бренд: ELNA Страницы: 2

Бренд: Singer Страницы: 15

Бренд: Consew Страницы: 26

Бренд: A-S-S Страницы: 7

Бренд: AIRBLAST Страницы: 43

Бренд: Singer Страницы: 32

Бренд: Olivetti Страницы: 216

Бренд: Pfaff Страницы: 130

Бренд: BoomToneDJ Страницы: 14

Бренд: Blaupunkt Страницы: 68

Бренд: JUKI Страницы: 15

Бренд: Newlong Страницы: 28

Бренд: Gottlieb Страницы: 74

Бренд: Nilfisk-Advance Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды