background image

3

HUSKYTOOLS.COM 

Please contact 1-888-43-HUSKY for further assistance.

pts-205109-051012,

 pts-2053019-053012,

 pts-206067-060612

Walney Road, Fifth Floor, Chantilly, VA 

20151-2923, (703) 788-2700, www.

cganet.com. Any such additional 

equipment has not been examined and 

no implication of proper use for 

breathing air is intended or implied. 

PERSONAL SAFETY 

 

WARNING:

 Operating any 

power tool can result in foreign 

objects being thrown into your 

eyes, which can result in severe 

eye damage. Before beginning 

operation, always wear safety 

goggles, safety glasses with 

side shields, or a full face shield 

when needed. Always use eye 

protection marked to comply 

with ANSI Z87.1.  

 

WARNING:

 

This product 

contains chemicals known to 

the State of California to cause 

cancer and birth defects or other 

reproductive harm.

 

Wash hands 

after handling.

 

1. 

Use safety equipment. 

Always wear eye 

protection with side 

shields when operating power tools. 

Dust mask, nonskid safety shoes, hard 

hat, or hearing protection must be used 

for appropriate conditions. 

2.  

Stay alert when operating a 

power tool. Do not use the 

tool while tired or under the 

influence of drugs, alcohol, or 

medication. 

3.  

Do not wear loose 

clothing or jewelry. 

Contain long hair. Keep 

your hair, clothing, and gloves away 

from moving parts. Loose clothes, 

jewelry, or long hair can be caught in 

moving parts. 

4.   Keep proper footing and balance at 

all times. Proper footing and balance 

enables better control of the tool in 

unexpected situations.

5.   Do not use on a ladder or unstable 

support.

6. 

Never touch any exposed metal 

parts on compressor during or 

immediately after operation. 

Compressor will remain hot for several 

minutes after operation. Do not reach 

around protective shrouds or attempt 

maintenance until unit has been 

allowed to cool.

8. 

The compressor is too heavy to be 

lifted by one person. Obtain 

assistance from others before 

lifting.

TRANSPORTING

1. 

Always place compressor on a 

protective mat when 

transporting to protect against 

damage to vehicle from leaks. Remove 

compressor from vehicle immediately 

upon arrival at your destination.

2.  Always transport and store unit in an 

upright position.

AIR COMPRESSOR AND  
PNEUMATIC TOOL SAFETY

 

WARNING: 

Do not attempt 

to modify this tool or create 

accessories not recommended 

for use with this tool. Any such 

alteration or modification is 

misuse and could result in a 

hazardous condition leading to 

possible serious personal injury.

 

 

CAUTION:

 

Do not use in an 

environment that is dusty or 

otherwise contaminated. Using 

the air compressor in this type of 

environment may cause damage 

to the unit.

1.   Keep compressors as far from the 

spraying area as possible, at least 15 ft. 

(0.4 m) from the spraying area and all 

explosive vapors.

Safety Information (continued)

Содержание C601H





























Отзывы: