HURST 3910201 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 12

HURST 3910201 Скачать руководство пользователя страница 8

Technical

Support

(707)

544

‐

4761

8

www.HURST

‐

SHIFTERS.com

STEP 21.

Carefully lower vehicle. From inside

the vehicle, attach the HURST upper stick to the
lower stick with two (2) stick mounting washers
and two (2) stick mounting screws and tighten.

TOOL: 7/32 Hex Wrench (Allen Key)

STEP 22.

OPTIONAL: ISOLATOR INSTALLATION

The provided neoprene isolators can be installed to
help reduce some of the transmission noise that
may be transmitted through the shifter stick. Install
one or both of the isolators between the lower stick
and the upper stick. Attach using two (2) washers
and two (2) screws and tighten.

NOTE: The isolators may not eliminate ALL
transmission noise or vibration and may reduce
shift feel and overall strength of the system.

STEP 23.

Reinstall the rubber boot that was

removed in STEP 5. Push down the lower lip of the
boot through the vehicle’s tunnel to ensure a
proper seal. With the boot in place, test the shifter
operation. Move shifter through all the gears and
make sure that it engages each gear fully and that
the stick moves freely from side to side in the
Neutral position. The knob may be temporary
installed to aid in testing.

«
...
6
7
8
9
10
...
»

Содержание 3910201













Отзывы:

Нет отзывов