HURST 3910201 Скачать руководство пользователя страница 1

 

 

 
 

 

WORK SAFELY! 

For maximum safety, perform this installation on a clean, level surface and with the 

engine turned off. Place blocks or wedges in front of and behind both rear wheels to prevent 
movement in either direction. 
 

CAUTION: 

To avoid any possibility of bodily injury or damage to vehicle, do not attempt installation 

until you are confident that the vehicle is safely secured and will not move.

 

 

NOTE:

 FOR PHOTOGRAPHIC PURPOSES, A 2010 MUSTANG IS SHOWN THROUGHOUT 

THESE INSTRUCTIONS. 2005-2009 GT KITS INSTALL WITH IDENTICAL STEPS. 

 

PARTS

 

 

 

 

 
 
 
 
 
 
 

 
 
 
 
 
 
 
 

Technical

 

Support

 

(707)

 

544

4761

  

 

 

 

       

1

 

 

 

         

      

         

www.HURST

SHIFTERS.com

 

Installation Instructions 

HURST COMPETITION AND BILLET/PLUS SHIFTER

2005-2010 Mustang w/5-speed Manual Transmission (GT only) 

  

Catalog# 3910201 

Knob 

Hurst Stick 

Shifter (3915201 shown) 

Knob Nut 

 

 

Stick Mounting 

Screws (2) 

Stick Mounting 

Washers (2) 

Neoprene 

Isolators (2) 

Boot Support and Zip Tie 

Содержание 3910201













Отзывы: