manualshive.com logo in svg

Hunter WHISPERWIND 2000, Инструкция по установке и эксплуатации, Страница: 16 / 24

Поделиться
Скачать
Hunter WHISPERWIND 2000 Скачать руководство пользователя страница 16

16

41277-01 05/98

®

ATTACHING SPEED RING™
COVER

1. Remove plug button as shown in

Figure 6e.

2. Remove the switch housing cover

and switch housing cap by remov-
ing the two screws as shown in
Figure 6e. Do not discard the
screws, cover, or cap.

Note:

 If you are installing a

Hunter light fixture, proceed to
“STEP 7 – ATTACHING LIGHT
FIXTURES.” If you do not wish to
use the integral light fixture, or
purchased a fan without a light
fixture, proceed with sub-steps 3-
6.

3. Place the Speed Ring™ cover on

top of the switch housing cover
as shown in Figure 6e.

4. Return the switch housing cover

to its original position. The Speed
Ring™ cover should now sit firmly
between the switch housing and
the switch housing cover.

5. Replace and tighten the screws

you removed in sub-step 2.

6. Replace the switch housing cap

and plug button.

You are now finished installing your
Whisperwind 2000™ fan. Turn to
“OPERATING YOUR HUNTER FAN”
for additional instructions.

Figure 6e - Attaching Speed Ring™
Cover

Plug Button

Switch
Housing
Cover

Speed
Ring™
Cover

Switch
Housing Cap

Содержание WHISPERWIND 2000

























Отзывы:

Нет отзывов