Hunter WHISPERWIND 2000 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 24

Hunter WHISPERWIND 2000 Скачать руководство пользователя страница 10

10

41277-01 05/98

®

4. Attach the canopy tightly to the

fan assembly with three #8-32 x
3/4" assembly screws and #8
lockwashers as shown in Figure
3d.

Note:

Pipe, ball, and setscrew not

used for flush mounting.

Standard and Angle Mounting
(For 8-foot Ceilings and Higher)

1. Fasten the fan housing to the

motor hanger adapter with three
#8-32 x 3/4" assembly screws and
#8 lockwashers as shown in Fig-
ure 3e.

Figure 3d - Attaching Canopy to Fan
Assembly

Figure 3e - Attaching Housing to
Motor Hanger Adapter

Assembly Screw
and Lockwasher

Motor Hanger
Adapter

Assembly Screw and
Lockwasher

Fan Housing

Figure 3f - Inserting Pipe through
Canopy

Pipe

Canopy

Pipe
Setscrew

3. Screw pipe into fan assembly un-

til tight.

IMPORTANT!

Tighten

pipe setscrew as shown in Figure
3f. Failure to tighten screw can
cause fan to fall.

2. Insert the pipe through the

canopy as shown in Figure 3f.
Feed wires from the fan through
the pipe.

CAUTION

The pipe has a special coating
on the threads. Do not remove
this coating; the coating pre-
vents the pipe from unscrew-
ing. Once assembled, do not
remove the pipe.

«
...
8
9
10
11
12
...
»

Содержание WHISPERWIND 2000

























Отзывы:

Нет отзывов