Hunter 28198 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 11

Hunter 28198 Скачать руководство пользователя страница 9

© 2005 Hunter Fan Company

41857-01 02/22/2005

9

Figure 27 - Receiver jumper switches

installing the switch housing

attaching the upper switch housing

1.

Partially install two #6-32 x 3/8" housing assembly screws into
the switch housing mounting plate as shown in Figure 28.

2.

Feed the upper plug connector through the center opening of
the upper switch housing. See Figure 28.

Figure 28 - Attaching the upper switch housing to the

mounting plate

3.

Align the keyhole slots in the upper switch housing with the
housing assembly screws installed previously.

4.

Turn the upper switch housing counterclockwise until the
housing assembly screws are firmly situated in the narrow end
of the keyhole slots as shown in Figure 29. Install the one re-
maining #6-32 x 3/8" housing assembly screw into the third
hole in the upper switch housing. Tighten all three screws firmly.

Figure 29 - Mounting the upper switch housing

CAUTION: Make sure the upper switch housing is se-

curely attached to the switch housing mounting plate. Fail-
ure to properly attach and tighten all three housing assem-
bly screws could result in the switch housing and light fix-
ture falling.

attaching the lower switch housing

1.

First insert the plug from the upper housing into the plug re-
ceptacle in the receiver module.
NOTE: The plug is polarized and will only go together one
way. Make sure you have correctly aligned plug and receptacle.

Figure 30 - Connecting the plug connectors

2.

Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower
switch housings. Attach the lower switch housing to the up-
per switch housing with three #6-32 x 3/8" housing assembly
screws. See Figure 30.
NOTE: If the two pieces are difficult to assemble, check the
alignment of the (3) slots in the top of the receiver module
and the mounting holes in the lower switch housing. They
should align together.

installing accessory light fixtures

To install the light fixture, follow the instructions included with the
light fixture for wiring, mounting, and assembly.

Receiver Bottom

Jumper
Switch

Lower Switch Housing

Pull receiver
out of switch
housing

Switch Housing
Mounting Plate

Upper Switch
Housing

Housing
Assembly
Screw

Upper Plug
Connector

Assembly Screw

Plug Connector

Upper Switch
Housing

Lower Switch
Housing

«
...
7
8
9
10
11
»

Содержание 28198












Отзывы:

Нет отзывов