background image

2

Hunter Fan Company 

41869-01 • 03/12/04

3

41869-01 • 03/12/04 

Hunter Fan Company

Installer’s Choice and Optional Accessories

Understanding Mounting and Installer’s Choice

®

Hunter’s patented 3-position mounting system provides you maximum 
installation fl exibility and ease. You can install your Hunter fan in one 
of three ways, depending on ceiling height and your preference: Low 
Profi le, Standard, or Angle mounting.  e steps in this manual include 
instructions for all three Installer’s Choice mounting methods.

Considering Optional Accessories

Consider using Hunter’s optional accessories, including a wall-mounted 
or remote speed control. To install and use the accessories, follow 
the instructions included with each product. For quiet and optimum 
performance of your Hunter fan, use only Hunter speed controls.

Low Profi le Mounting

 fi ts close to the 

ceiling, for recommended or low ceilings 
less than 8 feet high

Standard Mounting

 hangs from 

the ceiling by a downrod (included), 
recommended for ceilings 8 feet or higher 

Angle Mounting

 recommended for a 

vaulted or angled ceiling

For ceilings higher than 8 feet, you 
can purchase Hunter extension 
downrods. All Hunter fans use sturdy 
3/4” diameter pipe to assure stability 
and wobble-free performance. 

Содержание 21403


















Отзывы: