Hunter Douglas Luminette PowerGlide 2.1 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 36

Hunter Douglas Luminette PowerGlide 2.1 Скачать руководство пользователя страница 20

INSTALLATION

18

Test Headrail Operation

Use the manual control button on the satellite eye to test the operation of the headrail.

■

Test the traverse function.

➤

Press and release the button to traverse the
carriers across the full length of the headrail.

➤

Press and release the button a second time to
traverse the carriers to the fully stacked position.

➤

Pressing the button while the fabric carriers are
traversing will stop the traverse at that point.

■

Test the tilt function.

➤

When the carriers are fully traversed across the headrail, press and hold the button for
approximately 3 to 5 seconds to test the tilt function.

➤

Press and hold the button a second time to tilt in the other direction.

➤

To stop the tilt function, release the manual control button.

Attach the Fabric Panel(s)

Preparations

■

Use the manual control button on the satellite eye to stack the carriers.

■

Stand the tube on end on a clean surface with the header at the top. Position
the tube at the end of the headrail where the fabric stacks.

■

If the tube is too long to stand on end, carefully and safely use a utility knife
to trim the tube to an appropriate length. Do not unroll the fabric until you
begin attaching the vanes to the pinion clips.

CautIon:

Be very careful when trimming the tube to avoid damaging the

fabric in any way.

■

Remove the protective wrapping from the fabric.

Manual Control Button

Tube

Fabric

Panel

«
...
18
19
20
21
22
...
»

Содержание Luminette PowerGlide 2.1





































Отзывы:

Нет отзывов