Hunter Douglas LiteRise Скачать руководство пользователя страница 17

Страница: 17 / 28

INSTALLATION

Complete the Installation

Attach the Hook Wand (If Ordered)

If the blind was ordered with a hook wand, attach the wand to the metal shaft.

■

Pull the plastic sleeve from the top of the wand and insert it over the metal shaft.

■

Insert the hook on the wand through the hole in the metal shaft.

■

Slide the plastic sleeve down over the hook until firmly seated.

■

Test the wand. Approximately six revolutions of the wand should tilt the slats from fully
closed up to fully closed down.

Attach the Snap-On Wand (If Ordered)

If the blind was ordered with a snap-on wand, attach the wand to the metal shaft.

■

Connect the snap-on wand to the metal shaft.

■

Test the wand. Approximately six revolutions of the wand should tilt the slats from fully
closed up to fully closed down.

Plastic

Sleeve

Hook

Metal

Shaft

Slide

Sleeve

Over

Shaft

Hook

Through

Hole

Slide

Sleeve

Over

Hook

Snap-on

Connector

Wand

Metal

Shaft

Push

Up to

Attach

Wand

Check for

Secure

Attachment

Hook Wand

Snap-on Wand

Wand

Plastic

Sleeve

Hook

Metal

Shaft

Slide

Sleeve

Over

Shaft

Hook

Through

Hole

Slide

Sleeve

Over

Hook

Snap-on

Connector

Wand

Metal

Shaft

Push

Up to

Attach

Wand

Check for

Secure

Attachment

Hook Wand

Snap-on Wand

Wand

Содержание LiteRise





























Результаты поиска

Содержание LiteRise

Отзывы:

Похожие инструкции для LiteRise

Бренды по названию

Популярные бренды

Hunter Douglas LiteRise, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LiteRise

Отзывы:

Похожие инструкции для LiteRise

Бренды по названию

Популярные бренды