background image

TESTING THE INSTALLATION 

 
After installation is complete and all connections are made, you are ready to test the installation prior to 
actual use. Thorough testing should be performed with the boat in water, however, you can initially 
confirm basic operation with the boat trailered. 
 
Press POWER once to turn the unit on. There will be an audible chirp when any button is pressed that 
confirms the button press. If the unit does not power-up, ensure that the unit is fully seated on the mount 
and that power is available. 
 
The first screen provides three options; Start-up, Simulator, and Diagnostic. The time remaining before 
the screen "times-out" is shown at the bottom of the screen. If you do not press any button before the 
timer reaches 0, the normal operation screen will be displayed. If the boat is on-water, sonar data will 
begin to appear. 
 
If the bottom is visible on-screen with a digital depth readout, the unit is working properly. If the unit 
powers-up but fails to display bottom information, the transducer is not properly connected. Ensure that 
the boat is in water 
greater than 2' but less than 600' deep, and that the transducer is fully submerged. Remember that the 
sonar signal cannot pass through air. Refer to the troubleshooting section of this manual. If the unit is 
working properly, gradually increase the boat speed to test high-speed performance. If the unit functions 
well at low speeds but begins to skip or miss the bottom at higher speeds, the transducer installation 
requires adjustment. Refer to the appropriate transducer installation section for more detail. 
 
NOTE: It is often necessary to make several incremental transducer adjustments before optimum high-
speed performance is achieved. 
 

 

 
The Wide 128 is completely automatic and easy to use. Simply press the POWER button and the unit will 
locate and track the bottom from 2' to 600' changing ranges as necessary, display any structure or 
suspended fish and work at speeds from 0 to over 70 mph. 
 
If POWER is the only button you use, you will benefit from the advanced automatic bottom tracking of the 
Wide 128. However, if you choose to experiment with the many features and controls the Wide 128 
offers, you can customize the presentation of information to suit your particular needs. 
 
 

 
 
 
 

 

Содержание Wide 128

























Отзывы: