background image

Bottom Alarm 

 
The Wide One Hundred contains an audible alarm to warn you of shallow water depths. This 
alarm is adjustable from 2' to 99' of depth. To enable the alarm, simply adjust the alarm depth 
using the UP and DOWN arrow buttons, and press ENTER. Whenever the depth of the water 
beneath your boat is equal to or less than the selected alarm depth, a continuous alarm will 
sound. 
 

 

 
To disable the alarm, either move to deeper water, or select the Bottom Alarm menu, and press 
ENTER to turn the alarm off. 
 
 

Fish Alarm 

 

The Fish Alarm alerts you to the presence of fish, or other 
targets not attached to the bottom, in the water beneath your 
boat. The Fish Alarm has 3 different settings which correspond 
to the 3 different size fish targets shown on-screen. 
 
To enable Fish Alarm, use the UP and DOWN arrow buttons to 
adjust the size return you want to be alerted to; large fish only, 
large and medium size fish, or all fish. Then press ENTER to 
enable the alarm. When Fish Alarm is on, an onscreen indicator 
will be shown. 
 
Remember that it is impossible for sonar to determine if a signal 
return is a fish or some other type of object or suspended 
debris. Any object not connected to the bottom is normally a 
fish and is portrayed as a fish symbol. The strength of the 
reflected sonar signal from a target is a good indicator of the 
size of the target, and the fish symbol displayed represents the 

strength of the signal reflected from it. 
 
 
 

 
 
 
 
 

Содержание Wide 100





























Отзывы: