Hughes HN9400 Скачать руководство пользователя страница 103

Страница: 103 / 134

Note:

The TxCode shown is an example.

Confirming that TCP Acceleration is operational

TCP Acceleration is a proprietary Hughes protocol that optimizes performance for TCP/IP-based
applications, including faster downloads over satellite.

To determine if TCP acceleration is operational:

At the System Control Center, click the

System Status

link.

The System Status page appears.

Figure 73: Confirming that TCP Acceleration is operational

Check the

TCP Acceleration Status

field.

If the TCP Acceleration Status is

Operational

, TCP Acceleration is enabled and working

properly. Proceed to

Confirming that Web Acceleration is operational

on page 92.

If the TCP Acceleration Status is

Disabled

, restart the router:

a) Go to the System Control Center home page.
b) In the Help section, click

Restart HN9400

If TCP Acceleration is still disabled, power cycle the router:

a) Unplug the power cord from the power source.
b)

If the router is connected to a DC power source,

unplug the DC input cable from the

satellite router’s power supply.

c) Wait 10 sec.
d) Plug the power cord back into the power source.
e)

If the power source is DC,

plug the input cable back into the power supply.

Do not power cycle the satellite router by unplugging

the power cord from the router’s rear panel. Doing so could result in static electricity discharge

HN9400 Satellite Router Installation Guide

1038554-0001 Revision B

Chapter 8

Troubleshooting

Содержание HN9400







































































































































Результаты поиска

Содержание HN9400

Отзывы:

Похожие инструкции для HN9400

Бренды по названию

Популярные бренды

Hughes HN9400, Руководство по установке

Результаты поиска

Содержание HN9400

Отзывы:

Похожие инструкции для HN9400

Бренды по названию

Популярные бренды