Hughes Network Systems GMH2000 Скачать руководство пользователя страница 21

Страница: 21 / 105

8018653 1.1

Introduction • 1-7

CUMC receive functions include the following:

• Downconvert the appropriate RF channel under software control.

• Demodulate and perform diversity combining.

• Based on the operational mode, perform the baseband and error

control processing functions on the demodulated signal.

• Support control channels, traffic channels, and scanning receivers.

M6100 DIGITAL/ANALOG

TELEPHONE

TRANSCEIVER

UNIT

SND

PWR

END

RCL

CLR

FCN

DEF

MNO

WXY

ABC

JKL

TUV

GHI

PRS

OPR

Digital

InUse

FCN

RCL

CLR

SND

PWR

END

Figure 1-6. M6100 telephone and transceiver unit

1.5

Mobile station

The MS typically consists of an M6100™ digital/analog cellular
telephone and a transceiver unit (see figure 1-6).

M6100 digital/analog

cellular telephone

M6100 cellular telephone features include the following:

• Support for AMPS, IS-54, and E-TDMA standards.

• Memory that stores up to 99 phone numbers.

• Two hot keys that store frequently called numbers.

• A 12-button dual-tone multi-frequency (DTMF) keypad.

• A vacuum fluorescent display with signal strength indicator.

Содержание GMH2000









































































































Результаты поиска

Содержание GMH2000

Отзывы:

Бренды по названию

Популярные бренды

Hughes Network Systems GMH2000, Руководство по установке и обслуживанию

Результаты поиска

Содержание GMH2000

Отзывы:

Бренды по названию

Популярные бренды