manualshive.com logo in svg

Huffy 211014, Руководство пользователя

Поделиться
Скачать
Huffy 211014 Скачать руководство пользователя страница 2

2

P/N 211014

03/05

   

201246

11/04

In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN 

SERIOUS INJURY AND/OR PROPERTY DAMAGE.

Owner must ensure that all players know and follow these 

rules for safe operation of the system.

WARNING

•  DO NOT HANG on the rim or any part of the system including 

backboard, support braces or net.

•  During play, especially when performing dunk type activities, 

keep player's face away from the backboard, rim and net. 
Serious injury could occur if teeth/face come in contact with 
backboard, rim or net.

•  Do not slide, climb, shake or play on base and/or pole.
•  After assembly is complete, fill system completely with water or 

sand and stake to the ground. Never leave system in an upright 
position without filling base with weight, assystem may tip over 
causing injuries.

•  When adjusting height or moving system, keep hands and 

fingers away from moving parts.

•  Do not allow children to move or adjust system.
•  During play, do not wear jewelry (rings, watches, necklaces, 

etc.). Objects may entangle in net.

•  Surface beneath the base must be smooth and free of gravel or 

other sharp objects. Punctures cause leakage and could cause 
system to tip over.

•  Keep organic material away from pole base. Grass, litter, etc. 

could cause corrosion and/or deterioration.

•  Check pole system for signs of corrosion (rust, pitting, 

chipping) and repaint with exterior enamel paint. If rust has 
penetrated through the steel anywhere, replace pole 
immediately.

•  Check system before each use for proper ballast, loose 

hardware, excessive wear and signs corrosion and repair before 
use.

•  Check system before each use for instability.
•  Do not use system during windy and/or severe weather 

conditions; system may tip over. Place system in the storage 
position and/or in an area protected from the wind and free from 
personal property and/or overhead wires.

•  Never play on damaged equipment.
•  See instruction manual for proper installation and maintenance.
•  When moving system, use caution to keep mechanism from 

shifting.

•  Keep pole top covered with cap at all times.
•  Do not allow water in tank to freeze. During sub-freezing 

weather add non-toxic antifreeze, sand or empty tank 
completely and store. (Do not use salt.)

•  While moving system, do not allow anyone to stand or sit on 

base or have added ballasting on base.

•  Do not leave system unsupervised or play on system when 

wheels are engaged for moving.

•  Use Caution when moving system across uneven surfaces. 

System may tip over.

•  Use extreme caution if placing system on sloped surface. 

System may tip over more easily.

BEFORE YOU START!

To ensure optimal playability of backboard system, a

close tolerance fit between the elevator components

and hardware is required. Test-fit large bolts into large

holes of elevator tubes, backboard brackets, and

triangle plates. Carefully rock them in a circular

motion to ream out any excess paint from holes if

necessary.

Not all items pictured are included with every model.

Содержание 211014































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды