background image

have been sprayed.  Consult with the manufacturer of the chemicals in 
use to obtain proper instructions.   

HOW TO CLEAN & MAINTAIN: 

  

   

1.  Remove cap and pour out remaining solution, then rinse all parts 

thoroughly with clean water.   

2.  Leaving approximately ½ gallon of fresh water in tank, pressurize and 

flush pumping system by depressing trigger at least 2 minutes then drain 
all remaining water.   

3.  Always store tank clean and empty in a dry, shaded location.   

 

  

Please read and follow all instructions before using sprayer.

 

  

   



Before using, filling or cleaning any sprayer, read all parts of the 

operating instructions.   



Make sure to set up the sprayer exactly as explained above.   



Wear protective clothing, respirator, gloves, eye protection, etc. 

whenever using, filling or cleaning sprayer.   



Periodically re-grease lid gasket as well as lid vent and pump cylinder, 

where applicable.   



To ensure good performance, keep lid vent free of obstruction.  Before 

and after each use, make sure all connections are well tightened.  Service 
and replace worn parts as required.   



Read and follow all instructions of the chemical suppliers.   



As a rule, mix your chemicals in a separate container from which to fill 

the sprayer.  Do not mix formulas inside the sprayer.  When an exception 
is made (e.g. with liquid fertilizers), fill sprayer with water BEFORE adding 
the active ingredient.   



Always sift formula through the screen.  IF there is no built-in strainer, 

use a screened funnel. 



Never fill the sprayer with hot liquids.  Maximum  

30

°

C or 85

°

F.   



This sprayer is made to handle agrochemicals in their usual water or oil 

solutions.  Do not use flammable, corrosive or caustic solutions.   



Never use gasoline or other flammable materials.   



Before cleaning or servicing the sprayer, allow all pressure to escape.   

Do not store or transport sprayer under pressure.   



After each use, wash the sprayer 

– including hose, lance and shut off 

valve 

– with plenty of fresh water.  Unless spraying is to be continued 

within hours, drain chemical formula and thoroughly rinse the tank and all 
liquid ducts.   



Never store chemicals in your sprayer for any length of time.   

Содержание SP0







Отзывы: