background image

SF32 BobTail® Installation Tooling 

(HK1180)

         

                       

 Alcoa Fastening Systems & Rings

8

 





 





Figure 1

t

ool

 

to

 p

owerIg

 s

etup

 

1 .  Set Pull and Return pressures on Powerig using 

Huck Gage P/N: T-124833CE and 

Table 1

 .

2 .  First connect the Hydraulic Hoses to the Powerig .

3 .  Connect the other end of the Hose Assembly to the 

installation tool .

4 .  Connect the Trigger/Control Cord from the Tool to 

the Hose Assembly .

5 .  Connect the Trigger/Control Cord from the Hose 

Assembly to the Powerig .

 

6 .  Once the system is set up, turn on Powerig 

and install test fastener . Check to be sure that 

the fastener is installed correctly . This can be 

checked by using the appropriate swage gauge . 

WARNING: To prevent tripping hazard, 

suspend tools and route hoses off of 

floors.

WARNING: Only use compatible 

equipment with this tool.

p

ressure

 s

ettIngs

Table 1

Fastener 

Size

Grade 5

Pull (psi)

Grade 5

Return 

(psi)

Grade 8

Pull (psi)

Grade 8

Return 

(psi)

Class 8.8

Pull (psi)

Class 8.8

Return 

(psi)

Class 10.9

Pull (psi)

Class 10.9 

Return 

(psi)

-24 (3/4”)

5100

2700

7700

3800

-

-

-

-

20mm

-

-

-

-

5100

2700

7700

3800

Содержание BobTail SF32

















Отзывы: