Huchez PRIMO INOX BT 1000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 26

Huchez PRIMO INOX BT 1000 Скачать руководство пользователя страница 9

©

2011 by Huchez Treuils S.A.S.

Translation of the original instructions manual

9

UK

Reproduction prohibited

8 - Installation and set-up

8.1 Installation

The service life of a winch depends on its installation and set-up.
It is essential that you read this manual carefully before installing, using and servicing your
machine.
Any use which contravenes our instructions may create a hazard. In this case, the
manufacturer cannot accept any liability.



Do not use this machine before having read and understood the instruction manual in its
entirety



Always keep the manual close to the machine, available to the operator and the
maintenance officer



Comply and ensure compliance with the safety rules

Connect to the power supply (see 8.3 Power supply)
Check the rope and hook
Ensure you are ready to press the emergency stop button at all times, with no load attached,
then check that the movement of the hook corresponds to the direction of the arrows indicated
on the control unit.

Check that the brake works: with a nominal load attached, lift the load and lower it again or, in
the case of pulling, pull this load.
Check that the limit switch works.
The winch has been subjected to dynamic and static tests in the factory (cf. Test record).

8.2 Place of installation

These  winches  must  be  installed  and  bolted  to  a  flat,  solid  and  secure  surface  capable  of
bearing  the  loads  to  which  it  will  be  subjected.  An  unsuitable  installation  site  may  lead  to
serious accidents.
To assess the suitability of the place of installation and its resistance to loads, you must take
into  account  any  possible  overloading,  the  weight  of  the  winch  itself  and  the  weight  of  the
options  and/or  accessories  fitted  to  it,  including  all  dynamic  forces.  The  winch  user  is
responsible for determining the place of installation. If in doubt with regard to the suitability of
a place of installation, contact a civil engineer or a statics specialist.

Tighten the clamping bolts correctly

Bolt / nut

Stainless steel screw / nut tightening torque class

70 N.m

M8

17

M16

140

8.3 – Rope outlets

«
...
7
8
9
10
11
...
»

Содержание PRIMO INOX BT 1000



























Отзывы:

Нет отзывов