manualshive.com logo in svg

Huchez PRIMO INOX BT 1000, Инструкция по эксплуатации, Страница: 16 / 26

Поделиться
Скачать
Huchez PRIMO INOX BT 1000 Скачать руководство пользователя страница 16

 

© 

2011 by Huchez Treuils S.A.S.

 

Translation of the original instructions manual

16

UK 

Reproduction prohibited

 

 

 

11 – Spare parts 

If  during  maintenance  operations  you  notice  that  certain  parts  of  your  winch  need  to  be 
replaced, use HUCHEZ original parts only. 
 
For all spare parts orders, please indicate the following specifications on your order  
 

 

The type and capacity of the winch (indicated on the nameplate). 

 

The serial number and year of manufacture (indicated on the nameplate). 

 

The number or designation of the desired parts (exploded view). 

 

 

12 – Operating faults 

 

Fault 

Possible cause 

Solution 

Motor does not start. 

Power supply cut. 

Check and correct the problem 

Check the emergency stop. 

Brake not released 

See "brake fault" 

The contactor does not respond, 

Control fault. 

Check the contactor control and 

eliminate the fault. 

Limit switch engaged. 

Check the limit switch. 

Motor does not start 

or starts with 

difficulty. 

The voltage or frequency varies 

considerably compared to the 

setting when starting. 

Improve the mains conditions. 

Check the cable sections. 

Motor revs and 

absorbs a lot of 

current. 

Brake not released. 

See "brake fault" 

Faulty winding. 

Take the motor to an approved workshop for 

repair. 

One supply phase missing. 

Check the power supply. 

Circuit breaker 

activated instantly. 

Short circuit in the power supply 

cables. 

Eliminate the short circuit. 

Short circuit in the motor. 

Have the fault corrected in an approved 

workshop. 

Power supply cables incorrectly 

connected. 

Correct the connection. 

Motor earth fault. 

Have the fault corrected in an approved 

workshop. 

Speed greatly 

reduced when 

loaded. 

Voltage drop. 

Increase the power supply cable section. 

Motor overheated 

(temperature 

measurement) 

Insufficient ventilation. 

Clear the ventilation lanes. 

Ambient temperature too high. 

Respect the authorised temperature range. 

Bad contact in the power supply 

cable (operates temporarily on 2 

phases) 

Eliminate the bad contact. 

Circuit breaker activated. 

Bad contact in the relays. 

Service factor exceeded (S1 to 

S10, DIN 57530), e.g. because 

start speed is too high. 

Adapt the service factor to the prescribed 

conditions; if necessary, call a specialist to 

determine the type of motor. 

Drive system too 

noisy 

Rotating parts vibrate. 

Check the balances, eliminate the cause of 

the vibrations. 

Foreign bodies in the ventilation 

lanes. 

Clean the ventilation lanes. 

Brake not released. 

Max. air gap exceeded due to 

worn lagging. 

Take the motor to an approved workshop for 
repair.

 

Motor does not 

brake. 

Incorrect air gap. 

Take the motor to an approved workshop for 
repair.

 

Brake lagging totally worn. 

Take the motor to an approved workshop for 
repair.

 

Содержание PRIMO INOX BT 1000



























Отзывы:

Нет отзывов