4
REFLECTOR INSTALLATION:
(See Figure 3A)
1. Reflector can be installed on the ground or while fixture is hanging. If installing on
the ground, it is best to place fixture on its side.
2. Locate the four (4) threaded protrusions from the bottom of the heatsink and align
them with the holes in the reflector.
3. Using the supplied hardware (#8 screws), fasten the reflector to the heatsink.
INSTALLATION INSTRUCTIONS
LENS INSTALLATION (If Optioned):
(See Figure 3B)
1. Once the reflector has been mounted to the upper assembly,then the lens can be installed.
2. Seat the lens into the bottom of the reflector
3. Orient Lens Mounting Ring such that short leg of the cross section is on top and install over the lip of the reflector and lens.
See Figure 3B.
4. While manually holding the ring together, install screw through bracket holes and thread on hexagonal nut and tighten till
snug.
FIGURE 3A
LENS MOUNTING
FIGURE 3B
LENS INSTALLATION (If Optioned):
(See Figure 3B)
1.
Once the reflector has been mounted to the upper assembly,
then the lens can be installed.
2.
Seat the lens into the bottom of the reflector
3.
Orient Lens Mounting Ring such that short leg of the cross
section is on top and install over the lip of the reflector and
lens. See Figure 3B.
4.
While manually holding the ring together, install screw through
bracket holes and thread on hexagonal nut and tighten till snug.
UTB2
INSTALLATION INSTRUCTIONS
Hubbell Lighting, Inc. Doc. No. 93097040
A subsidiary of Hubbell Incorporated Revision P0
701 Millennium Drive • Greenville, SC 29607 Page 4 Phone (864) 678-1000
REFLECTOR INSTALLATION:
(See Figure 3A)
1.
Reflector can be installed on the ground or while fixture is hanging. If
installing on the ground, it is best to place fixture on its side.
2.
Locate the four (4) threaded protrusions from the bottom of the heatsink
and align them with the holes in the reflector.
3.
Using the supplied hardware (#8 screws), fasten the reflector to the
heatsink.
FIGURE 3B
FIGURE 3A
LENS MOUNTING
FIGURE 3B
LENS INSTALLATION (If Optioned):
(See Figure 3B)
1.
Once the reflector has been mounted to the upper assembly,
then the lens can be installed.
2.
Seat the lens into the bottom of the reflector
3.
Orient Lens Mounting Ring such that short leg of the cross
section is on top and install over the lip of the reflector and
lens. See Figure 3B.
4.
While manually holding the ring together, install screw through
bracket holes and thread on hexagonal nut and tighten till snug.
UTB2
INSTALLATION INSTRUCTIONS
Hubbell Lighting, Inc. Doc. No. 93097040
A subsidiary of Hubbell Incorporated Revision P0
701 Millennium Drive • Greenville, SC 29607 Page 4 Phone (864) 678-1000
REFLECTOR INSTALLATION:
(See Figure 3A)
1.
Reflector can be installed on the ground or while fixture is hanging. If
installing on the ground, it is best to place fixture on its side.
2.
Locate the four (4) threaded protrusions from the bottom of the heatsink
and align them with the holes in the reflector.
3.
Using the supplied hardware (#8 screws), fasten the reflector to the
heatsink.
FIGURE 3B
GENERAL INFORMATION:
1. All 12” (304.8 mm) minimum supply wire outside of conduit.
2. Fixture mounting hook loop threads are ¾-14 NPS.
HOOK/LOOP MOUNTING: (Figures 5A, 5B & 5C)
Cord & Hook/Loop ordered as CxHLPx (Plug optional)
1. If not already done, assemble the hook loop pieces according to the following steps.
2. Thread the upper locknut (with flat surface down) onto the hook loop to approximately 1/8” from the top of the threads.
(Figure 5A)
3. Position the safety clasp as shown and just start the fastener, but leave loose. (Figure 5A)
4. Insert the power cord, must be rated minimum 90°C 16/3 SEOW-A or equivalent, through the hole in the hook and insert
gotcha ring, top washer, gasket, lower washer and cast bushing/nut onto cord. Fully tighten cast bushing against bottom of
hook. (Figure 5A)
5. Slide the assembly into the slot on the fixture yoke, so that the upper locknut is on top and the tightened cast bushing is on
the bottom and hand tighten the upper locknut. (Figure 5B)
