Page 2 Kim Lighting • 16555 E. Gale Ave. • P.O. Box 60080• City of Industry, CA 91716-0080• 626/968-5666 • FAX 626/330-3861
LAMP INSTALLATION OR REPLACEMENT:
Make certain the electrical supply is
OFF
before
starting lamp installation or replacement.
1. Remove fixture top cover by loosening the two screws
progressively and evenly.
2
Install or replace the lamp using only the type and
wattage shown on the fixture label. For installation, lamp
can be inserted through center of reflector stack.
3. Replace the cover making sure all gaskets are clean
and in place. Tighten the screws progressively to insure
even pressure on gaskets.
B30 Series 8
""
Round Bollard
Installation & Maintenance Instructions
KIM LIGHTING LIMITED WARRANTY
When installed in accordance with Kim Installation
Instructions and accepted trade practices, the following shall
apply:
General Product Limited Warranty Coverage
All material and component parts used in the manufacture of
Kim Products, are warranted to be free from defects of
material and/or workmanship for a period of 1 year from date
of sale, with the following exceptions:
Auxiliary Equipment
All auxiliary equipment (such as lamps, ballasts, and
transformers) provided by and/or included in Kim Products
shall carry the component manufacturer's warranty.
Copper and Bronze Landscape Components
Copper and Bronze Landscape fixture components shall be
warranted against defects of material and/or workmanship,
and failure due to corrosion, for a period of 25 years from
date of sale.
Composite In-Grade Components
Composite In-Grade fixture components installed below
grade, shall be warranted against defects of material and/or
workmanship, and failure due to corrosion, for a period of 7
years from date of sale.
Aluminum Landscape Components
Aluminum Landscape fixture components not in direct
contact with soil, shall be warranted against defects of
material and/or workmanship for a period of 3 years from date
of sale. Aluminum fixture components in direct contact with
soil shall be warranted from defects of material and failure
from corrosion for a period of 1 year from date of sale.
Limit of Liability and General Conditions
Only products which are installed, used and maintained in
accordance with applicable Kim instructions, specifications,
and accepted trade practices, are covered by the Kim
Warranty. During the warranty period, with proof of purchase,
Kim will repair or replace with the same or similar product, at
Kim's option, without charge. Labor costs are the owner's
responsibility and are excluded from this warranty. This
warranty is void if the product is modified, tampered with,
misapplied, poorly installed, improperly maintained, or
subjected to abnormal conditions.
Repair or replacement as provided under this warranty is the
exclusive remedy of the purchaser. This warranty is in lieu of
all other warranties, expressed or implied, including any
implied warranty of fitness for a particular application. Kim
Lighting shall not be liable to the purchaser for indirect or
consequential damages.
!
How may we serve you better?
Please let us know. Visit our website at:
www.kimlighting.com
Your concerns are important to us.
!
!
CLEANING REFLECTOR ASSEMBLY
AND PLASTIC LENS:
Make certain the electrical supply is
OFF
.
1. Remove fixture top cover by loosening the two screws
progressively and evenly.
2
Remove the lamp.
3. Loosen the three reflector mounting screws inside the
reflector assembly near the top of the lamp socket. Note
orientation of assembly before removing.
4. Rotate the reflector assembly clockwise and lift the
assembly off of the mounting screws.
5. Clean the plastic and the reflector assembly with a mild
detergent. Rinse and wipe dry.
DO NOT
use an
abrasive compound or attempt to clean with a dry cloth.
6. Replace the reflector assembly and tighten the three
reflector mounting screws. These screws are not
equally spaced and the reflector assembly will fit in only
one orientation.
7. Install the correct lamp as shown on the fixture label and
check all gaskets to be sure they are clean and in place.
8. Replace the cover. Tighten the screws progressively to
insure even pressure on the gaskets.
BALLAST REPLACEMENT:
Make certain the electrical supply is
OFF
before
starting ballast replacement.
1. Loosen two set screws at the base of the pole using a
F
" hex key.
2. Rotate the pole counter clockwise approximately 1" and
lift pole/fixture assembly upward to clear ballast
assembly.
3. Replace ballast with the correct type and wattage.
Connect all wiring as shown in the wiring diagram on
the new ballast.
4. Place the pole body over the ballast assembly and
slowly turn until the pole drops into retaining slots, then
twist clockwise to lock onto the base casting.
5
Tighten the two set screws at the base of the pole.
WARNING:
The H.I.D. / Fluorescent fixture utilizes a lamp that may
contain mercury. For information on disposal of lamp go
to website:
www.lamprecycle.org
