Huayu HYL-3000 Скачать руководство пользователя страница 3

Information on this Manual

Validity

This manual is valid for the following devices:HYL-3000/HYL-4000 /HYL-5000

Scope

This manual provides  the installation, operation and troubleshooting of this unit, please read this manual 

carefully before installations and operations.

Target Group

For qualified persons and end users. Qualified persons and end users must have the following skills:

Knowledge about this unit operation

Training in  deal with the security issues associated with installations and electrical safety

Training in the installation and commissioning of electrical devices and installations

Knowledge of the applicable local standards and directives

Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual 

for future reference.

All the operation and connection need to be operated by qualified persons.

Before using the unit, read all instructions and cautionary marking on the unit. Any  damage caused by 

inappropriate operation is not warranted by huayu .

All the electrical installation must comply with the local electrical safety standards.

Do not disassemble the unit. Take it to a qualified service center when service or repair is required, 

incorrect re-assembly may result in a risk of electric shock or fire. Do not open inverter cover or change 

any components without huayu's authorization, otherwise the warranty commitment for the inverter 

will be invalid.

To reduce risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning, 

turning off the unit will not reduce this risk.

CAUTION-To reduce risk of injury, charge only deep-cycle lead-acid type rechargeable batteries and 

lithium batteries, other types of batteries may burst, causing personal injury and damage.

NEVER charge a frozen battery.

For optimum operation of this unit, please follow required spec to select appropriate cable size and breaker.

Please strictly follow installation procedure when you want to disconnect AC or DC terminals, please refer 

to INSTALLATION section of this manual for the details.

GROUNDING INSTRUCTIONS -This unit should be connected to a permanent grounded wiring system, 

be sure to comply with local requirements and regulation to install this inverter.

NEVER cause AC output and DC input short circuited. Do not connect to the mains when 
DC input short circuits.

1.   Brief Introduction

1.1  Features of the Inverter

HYL series is a multifunctional, high frequency pure sine wave entry-level hybrid solar inverter, features:

Applicable for pure off grid/ backup power / self-consumption / on grid situation

Integrated with 2 MPPT solar charge controllers, MPPT ranges 120V~385V

Rated power 5KW, power factor 1

Be able to run with or without battery in ongrid and offgrid mode

With separated generator input interface, able to control generator remotely

Solar and utility grid can power loads at the same time

With integrated advanced parallel function, up to 10pcs max paralleling 

Support CAN/RS485 for Li-ion battery BMS communication

WIFI/ GPRS remote monitoring , setting and firmware update, support website, free IOS/Android APP

LOGIN

Solar Panel

Utility Grid

Generator

Battery

Wifi / 4G

Internet

Huayu View

Huayu Server

Home
Loads

01

02

Содержание HYL-3000





















Отзывы: