Huawei U8815 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 80

Huawei U8815 Скачать руководство пользователя страница 37

U8815
Maintenance Manual

9 Principles and Failure Analysis

Issue 1.0 (2012-02-13)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

28

Figure 9-9

Charging management circuit diagram 4



Analysis

U8815 adopts the PM8029 circuit management chip and integrates a charging scheme.
Three charging states are supported: trickle charging, constant current charging, and
constant voltage charging. All the preceding charging methods use the same charging
channel:

VEXT_DC -> VCHG -> VPH_PWR -> Q201, pin3 -> VBAT.

U8815 adopts the dedicated FAN5402UCX power supply chip for 1 A charging, and uses
I2C interfaces for communication and control: GPIO13 (I2C_SCL_DCDC) and GPIO13
(I2C_SCL_DCDC). The charging management chip obtains power from the VCHAG of
the USB port. The chip is controlled by the I2C. The output VPH_PWR supplies power
to the power management chip and the battery.

This chip supports three modes: charging mode, boost mode, and high resistance mode.
The charging mode is normal charging process. The boost mode is USB-OTG mode. The
high resistance mode is power-saving mode (standby mode) without charging.



Troubleshooting Process

There are two types of common charging failures:

−

The phone has no response after a charger is connected to it.

−

The phone displays an animated icon indicating that it is charging, but actually, the
battery is not charged.

−

To troubleshoot charging failure, firstly check whether the battery connector is
damaged.



No charging indicator is displayed after the charger is connected to the phone.



A charging indicator is displayed after the charger is connected to the phone but the
phone cannot be charged.

Figure 9-10 shows the troubleshooting process for charging failures.

«
...
35
36
37
38
39
...
»

Содержание U8815

















































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды