Huawei U8655N Скачать руководство пользователя страница 13

Страница: 13 / 72

U8655
Maintenance Manual

5 Software Upgrade

Issue 1.0 (2012-02-23)

Huawei Proprietary and Confidential

Software Upgrade

5.1 Upgrade Preparation

Category

Item

Description

Upgrade
environment

Computer

To copy upgrade software

microSD card

With more than 512 MB free space

Battery

With at least 30% power remaining

Upgrade file

Main upgrade pack

dload/UPDATE.APP

Vendor upgrade pack

vendor_XXX_XXX/UPDATE.APP

Upgrade
method

Using the microSD card Normal upgrade

Forcible upgrade

5.2 Upgrade Procedure

Format the microSD card.

Create a folder named

dload

in the root directory of the microSD card.

Copy the upgrade file to the

dload

folder.

Install the microSD card on the phone. Power the phone on, and enter

*#*#2846579#*#*

on the idle screen.

Select

SD Upgrade

then

Yes

to start the upgrade.

Before the upgrade, NV items backup is performed (if the phone's NV items has not
been backed up before). Then the phone restarts and the upgrade starts.

The upgrade progress is displayed on the LCD.

Содержание U8655N









































































Результаты поиска

Содержание U8655N

Отзывы:

Похожие инструкции для U8655N

Бренды по названию

Популярные бренды

Huawei U8655N, Руководство по обслуживанию

Результаты поиска

Содержание U8655N

Отзывы:

Похожие инструкции для U8655N

Бренды по названию

Популярные бренды